[Gasification] Scada (SCADA)

Leland "Tom" Taylor linvent at aol.com
Thu Apr 21 12:16:31 MDT 2016


Thanks for helping moving the industry out of the stone age.
Sent from my Virgin Mobile phone.

Mark Elliott Ludlow <mark at ludlow.com> wrote:

>I agree with Leland “Tom” Taylor completely. My last project was a DDS (Distributed Control System) and we employed 19, μ-controllers (microcontrollers), that had digital and analog IO, math primitives, plenty of power and were interconnected by plain old Ethernet. Data collection and storage was a no-brainer. Software development could proceed a subsystem at a time. I would never do anything different, unless I were stuck in a 1970 time warp. We used 19” touch screen monitors, placed wherever they were needed. Histograms of process performance (stability, rate, energy usage, etc.) were available anywhere, including my living room sofa. 
>
>On a later project in MX I used a Siemens Simatic system. Is was much less flexible, cost at least four-times as much and had distributed I/O collectors but not distributed process management intelligence. Tons more wiring. No redundancy. Proprietary architecture. Mostly much slower but that’d not be as much an issue on a gasifier as  it may be on motion control. And Siemens was years ahead of U.S offerings, who only until relatively only offered archaic Ladder Logic programming tools.
>
>Best, Mark
>
> 
>
>From: Gasification [mailto:gasification-bounces at lists.bioenergylists.org] On Behalf Of linvent at aol.com
>Sent: Thursday, April 21, 2016 7:40 AM
>To: gasification at lists.bioenergylists.org
>Subject: Re: [Gasification] Scada
>
> 
>
>or as those are obsolete, go with  a laptop with touch screen a USB port, a two wire or wireless interface to your sensors and control devices and a program that runs on your computer that doesn't need to be programed like the plc. 
>
>Sorry to hear that there are those out there who are still using the archaic plc architecture as it only makes for more work.
>
>Sincerely,
>
>Leland T. "Tom" Taylor
>
>Thermogenics Inc. 
>
> 
>
>-----Original Message-----
>From: Roland Siemons <siemons at cleanfuels.nl <mailto:siemons at cleanfuels.nl> >
>To: Discussion of biomass pyrolysis and gasification <gasification at lists.bioenergylists.org <mailto:gasification at lists.bioenergylists.org> >
>Sent: Thu, Apr 21, 2016 8:03 am
>Subject: Re: [Gasification] Scada
>
>Thanks, Manova!
>
>Greetz,
>
>Roland
>
>
>
>Clean Fuels B.V.
>Mail to: c/o University of Twente
>PO Box 217
>7500 AE Enschede
>The Netherlands
>
>Visiting address:
>Marconistraat 33A
>7575 AR Oldenzaal
>The Netherlands
>
>T: +31 (0)53 4892909
>M: +31 (0)64561 6734
>Siemons at CleanFuels.nl <mailto:Siemons at CleanFuels.nl> 
>www.cleanfuels.nl <http://www.cleanfuels.nl> 
>
>On 21/04/2016 13:09, Mano Va wrote:
>> Dear sir
>>
>> For this pyrolysis plant SCADA Automation not required because SCADA
>> Computer, Programme and Software cost are high so
>>
>> simply can go with PLC and HMI unit,and can achieve All customised
>> monitoring system like SCADA compare to SCADA its Cheaper
>>
>> PLC-Products OMRANG,DELTA its cheap ,ABB,GE,SIEMENS 
>>
>> Regards,
>>
>> Manova.M
>>
>> On Wed, Apr 20, 2016 at 4:44 PM, Roland Siemons <siemons at cleanfuels.nl <mailto:siemons at cleanfuels.nl> 
>> <mailto:siemons at cleanfuels.nl <mailto:siemons at cleanfuels.nl?> >> wrote:
>>
>> Hello List,
>>
>> We need a simple SCADA system for a small pyrolysis plant (450
>> kg/h input) that we are building.
>> Do you have any suggestions other than standard Siemens products?
>>
>> Best regards,
>>
>> Roland Siemons
>>
>>
>>
>>
>> Clean Fuels B.V.
>> Mail to: c/o University of Twente
>> PO Box 217
>> 7500 AE Enschede
>> The Netherlands
>>
>> Visiting address:
>> Marconistraat 33A
>> 7575 AR Oldenzaal
>> The Netherlands
>>
>> T: +31 (0)53 4892909 <tel:%2B31%20%280%2953%204892909>
>> M: +31 (0)64561 6734
>> Siemons at CleanFuels.nl <mailto:Siemons at CleanFuels.nl>  <mailto:Siemons at CleanFuels.nl <mailto:Siemons at CleanFuels.nl?> >
>> www.cleanfuels.nl <http://www.cleanfuels.nl>  <http://www.cleanfuels.nl>
>>
>>
>> _______________________________________________
>> Gasification mailing list
>>
>> to Send a Message to the list, use the email address
>> Gasification at bioenergylists.org <mailto:Gasification at bioenergylists.org> 
>> <mailto:Gasification at bioenergylists.org <mailto:Gasification at bioenergylists.org?> >
>>
>> to UNSUBSCRIBE or Change your List Settings use the web page
>> http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>
>> for more Gasifiers, News and Information see our web site:
>> http://gasifiers.bioenergylists.org/
>>
>>
>>
>>
>> _______________________________________________
>> Gasification mailing list
>>
>> to Send a Message to the list, use the email address
>> Gasification at bioenergylists.org <mailto:Gasification at bioenergylists.org> 
>>
>> to UNSUBSCRIBE or Change your List Settings use the web page
>> http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>
>> for more Gasifiers, News and Information see our web site:
>> http://gasifiers.bioenergylists.org/
>
>
>_______________________________________________
>Gasification mailing list
>
>to Send a Message to the list, use the email address
>Gasification at bioenergylists.org <mailto:Gasification at bioenergylists.org> 
>
>to UNSUBSCRIBE or Change your List Settings use the web page
>http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>
>for more Gasifiers, News and Information see our web site:
>http://gasifiers.bioenergylists.org/
>
>
>_______________________________________________
>Gasification mailing list
>
>to Send a Message to the list, use the email address
>Gasification at bioenergylists.org
>
>to UNSUBSCRIBE or Change your List Settings use the web page
>http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>
>for more Gasifiers,  News and Information see our web site:
>http://gasifiers.bioenergylists.org/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20160421/a6056698/attachment.html>


More information about the Gasification mailing list