<font color='black' size='2' face='arial'>
<div style="FONT-FAMILY: arial,helvetica; COLOR: black; FONT-SIZE: 10pt">

<div id=AOLMsgPart_2_8613f043-7ce0-4a10-b8e8-322d1e137ada><FONT color=black size=2 face=arial>

<div style="FONT-FAMILY: arial,helvetica; COLOR: black; FONT-SIZE: 10pt">

<div id=AOLMsgPart_2_b29600f2-8a25-45fe-8e7a-87fb14d6a6a9><FONT color=black size=2 face=arial>

<div>Who said anything about an "aluminum rotor" .What's wrong with an all plastic"hot tub pump".</div>


<div>Since I got into this discussion it seems obvious to me that I have made this Gas pump far  to complicated. </div>


<div>Producer gas used to be held in large water sealed telescopic cylinders, which rose up into the sky, lifted by coal gas pressure Did our Grandfathers pump them up on occasions with fresh air, get inside ,clean and paint, say  every "1000 hours" does this sound plausible?. Who cares if the plastic drums get dirty inside.</div>


<div>I am amazed how simple it is to create a vacuum with a little puff of steam into a container. the steam quickly displaces the air and if sealed, the contents (steam)</div>


<div>shrinks to approximately 1.4% of its original volume (condenses), creating a substantial vacuum.</div>


<div>1 psi equals about 27"WG.or 106 mm. so it seems to me a system could be easily devised using waste heat from the gasifier in order to pressurize the product for distribution. perhaps that's how the Chinese do it?</div>


<div> </div>


<div>GF</div>


<div> </div>


<div>  </div>


<div style="CLEAR: both"></div>
<br>
<br>


<div style="FONT-FAMILY: arial,helvetica; COLOR: black; FONT-SIZE: 10pt">-----Original Message-----<br>
From: praufast@free.fr<br>
To: Gasification@bioenergylists.org<br>
Sent: Wed, Feb 2, 2011 11:57 am<br>
Subject: Re: [Gasification] compression of dirty gas<br>
<br>


<div style="BACKGROUND-COLOR: #fff; MARGIN: 0px; FONT-FAMILY: Tahoma, Verdana, Arial, Sans-Serif; COLOR: #000; FONT-SIZE: 12px" id=AOLMsgPart_0_fe23bd93-d354-48d4-bc1c-1d2c7f941530><PRE style="FONT-SIZE: 9pt"><TT>"After a few hundred hours the compressor would look like the inside of a 
woodstove chimney.  It would be out of balance, shaking and there would be a 
toxic waste disposal problem.  The acids in the woodgas would also eat into the 
aluminum rotor.  Conceptually, a decent idea though. 
"

The water is continually recirculated and cooled, obviously it can also be 
cleaned or replaced with fresh water.
To clean it you can use something like a Voraxial separator : 
<A href="http://www.youtube.com/watch?v=-W8_GpMz9nI&feature=related" target=_blank>http://www.youtube.com/watch?v=-W8_GpMz9nI&feature=related</A>

Philippe.

_______________________________________________
Gasification mailing list

to Send a Message to the list, use the email address
<A href="mailto:Gasification@bioenergylists.org">Gasification@bioenergylists.org</A>

to UNSUBSCRIBE or Change your List Settings use the web page
<A href="http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org" target=_blank>http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org</A>

for more Gasifiers,  News and Information see our web site:
<A href="http://gasifiers.bioenergylists.org/" target=_blank>http://gasifiers.bioenergylists.org/</A>
</TT></PRE></div>
<!-- end of AOLMsgPart_0_fe23bd93-d354-48d4-bc1c-1d2c7f941530 --></div>
</FONT></div>
<!-- end of AOLMsgPart_2_b29600f2-8a25-45fe-8e7a-87fb14d6a6a9 --></div>
</FONT></div>
<!-- end of AOLMsgPart_2_8613f043-7ce0-4a10-b8e8-322d1e137ada --></div>
</font>