<font color='black' size='2' face='arial'>
<div>Jim,</div>


<div> </div>


<div>Why did you stick with 5" tube"?  I would try using a 6" or 8" chimney and just set the swirl burner under or slightly in it.  The swirl burner will act as a heat source to provide natural convection like a wood stove if you just want to get the smoke away from the operator.  </div>


<div> </div>


<div>Once you try to fire a boiler/heat exchanger with the flare you are looking at a different animal.  I bet the multiple narrow firetubes will move any resonance out of of your operating range.</div>


<div> </div>


<div>Stephen</div>


<div>-----Original Message-----<br>
From: jim mason <jim@allpowerlabs.org><br>
To: Discussion of biomass pyrolysis and gasification <gasification@lists.bioenergylists.org><br>
Sent: Mon, May 16, 2011 1:51 am<br>
Subject: Re: [Gasification] thermoacoutics, rijke tubes, sondhauss tubes, pulse jets-- how do we make them not work?<br>
<br>
</div>


<div style="FONT-FAMILY: arial,helvetica; COLOR: black; FONT-SIZE: 10pt">

<div style="BACKGROUND-COLOR: #fff; MARGIN: 0px; FONT-FAMILY: Tahoma, Verdana, Arial, Sans-Serif; COLOR: #000; FONT-SIZE: 12px" id=AOLMsgPart_0_fe261bf7-08bd-4b29-87b2-adb65fe2999a><PRE style="FONT-SIZE: 9pt"><TT>> we're having lots of problems with thermoacoustics now that we've put
> a tall stack on our gasifier swirl burner.  we're using a tall stack
> now to keep startup gasses away from the operator.  the swirl burner
> is 5" in diameter, 10" tall. we've added a 4 foot or so stack of the
> same 5" diameter. it looks like this
> <A href="http://www.gekgasifier.com/forums/showthread.php?t=501" target=_blank>http://www.gekgasifier.com/forums/showthread.php?t=501</A> (though this
> one without the joint at 10")


completing the circle on this question from a few months ago, here's
what we finally found solved the problem- insulation.  we found that
if we simply insulated the stack from bottom to top, eliminating the
hot/cold delta, the thermoacoustic effect went away.   more reading in
the rilke / sondhaus tube effect clarified that it needs this temp
differential, and if you eliminate the temp differential, the effect
stops (which it did).

this was one of the many good suggestions offered here.  we didn't try
all of them.  but some of note.

1.  cut a V in the top of the stack like done to quiet some pulse jets
2.  drill holes towards the top, or other shapes to soften the
transition at the end to reduce the pulse wave
3.  put a floating "deresonator" plate in the tube
4.  angle the tube, or otherwise put angle plates in it to break up
the standing wave.
5.  drill a hole in the side down low and put a rod across the flame path.
6.  experiment with expansion chambers like a two stroke exhaust,
except with the intent of "detuning".



i don't know which of the suggested will work.  we ultimately decided
the easiest one was the insulation and tried that.  it worked, so we
stopped there for now.

as usual, thank you for the input.

and btw, what problem of physics do gasifiers not touch?

j

_______________________________________________
Gasification mailing list

to Send a Message to the list, use the email address
<A href="mailto:Gasification@bioenergylists.org">Gasification@bioenergylists.org</A>

to UNSUBSCRIBE or Change your List Settings use the web page
<A href="http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org" target=_blank>http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org</A>

for more Gasifiers,  News and Information see our web site:
<A href="http://gasifiers.bioenergylists.org/" target=_blank>http://gasifiers.bioenergylists.org/</A>
</TT></PRE></div>
<!-- end of AOLMsgPart_0_fe261bf7-08bd-4b29-87b2-adb65fe2999a --></div>
</font>