<div class="gmail_quote">Sam - not sure where this has gone. Pursuit Dynamics seem to be on a new path. Maybe Dr Burns is still working on it.<br><a href="http://www.gizmag.com/go/1734/">http://www.gizmag.com/go/1734/</a><br>
<br><blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;">
Message: 1<br>
Date: Wed, 18 May 2011 21:03:36 +0100<br>
From: <a href="mailto:sam@bristolwireless.net">sam@bristolwireless.net</a><br>
To: <a href="mailto:gasification@lists.bioenergylists.org">gasification@lists.bioenergylists.org</a><br>
Subject: [Gasification] Underwater gasification?<br>
Message-ID:<br>
        <<a href="mailto:20110518210336.Horde.pzohfmOelG9N1CYYEoHR4lA@slackmail.co.uk">20110518210336.Horde.pzohfmOelG9N1CYYEoHR4lA@slackmail.co.uk</a>><br>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed; DelSp=Yes<br>
<br>
<br>
Hi all<br>
<br>
I wish to move a 22ft 1 tonne boat using wood power.<br>
<br>
I have already considered gasification + combustion, gasification +<br>
stirling engines, even steam power!<br>
<br>
My latest thought experiment is gasification + thermo-electric generators.<br>
<br>
looking at the products of <a href="http://tegpower.com" target="_blank">tegpower.com</a> it seems like this may be<br>
viable, if somewhat expensive (?4k)<br>
<br>
To move the boat at around three knots will take an estimated 40 -50<br>
amps <a href="http://www.floveroutboard.co.uk/outboards.html" target="_blank">http://www.floveroutboard.co.uk/outboards.html</a><br>
<br>
Which will require approximately 50 of the TEGP15 thermo electric<br>
panels <a href="http://www.tegpower.com/products.html" target="_blank">http://www.tegpower.com/products.html</a>. I then need to keep one<br>
side of the panel at 20C (or lower) and the other at 260C. (but no<br>
higher than 325C)<br>
<br>
Initially I considered doing this with an active water pump driven<br>
cooling system, which would be fine, however if the pump/wiring fails<br>
or gets blocked the considerable investment in TEG panels melts before<br>
your eyes.<br>
<br>
So I figured given all the water around the boat it might be better to<br>
run a passive cooling system, and actively pump the air for the<br>
gasifier. That way if something breaks it just cools down and stops<br>
working.<br>
<br>
Which leads me to the challenge of gasification underwater..<br>
<br>
I have taken as a benchmark the mega fireplace gasifer<br>
<a href="http://www.woodgas-stove.com/how_to_use_woodgas_stoves.php" target="_blank">http://www.woodgas-stove.com/how_to_use_woodgas_stoves.php</a> which puts<br>
out 55,000 btu/hr which on paper is enough power.<br>
<br>
So I am thinking about taking take a 14inch x 6ft diameter steel pipe<br>
with a sealed end and sticking a woodgas fireplace in it. Then feeding<br>
a air supply pipe down to the bottom, and using a fan to force the air<br>
in.<br>
<br>
The TEG units will be attached to the inside of the pipe with some<br>
kind of heat conducting cement. The water temperature outside the pipe<br>
(typically 5C - 15C) will provide the passive cooling, and the heat<br>
rising up from the stove will heat the inner panel (maybe!)<br>
<br>
I did a bad diagram here: <a href="http://i.imgur.com/SYpu2.jpg" target="_blank">http://i.imgur.com/SYpu2.jpg</a><br>
<br>
I realise the engineering challenges of this are not trivial..<br>
<br>
* Are forced updraft gasifiers harder to make/ less efficient on this scale?<br>
<br>
* What would be a good guesstimate for the temperature at the bottom<br>
TEG? The top TEG? Above 325C?<br>
<br>
The next step is to buy a the pipe and woodgas fireplace and do some<br>
real world tests. Is it worth me taking that next step? Do you see<br>
insurmountable problems?<br>
<br>
Thanks<br>
<br>
Sam<br>
<br>
<br>
<br></blockquote></div>