<html><head><meta http-equiv="content-type" content="text/html; charset=utf-8"></head><body dir="auto"><div>Another good trick is shredded cardboard and animal fats from cooking Easy start, raises the temp of firebox and refractory quickly, gets rid of excess cardboard, and fats, eliminates need of splitting feed stock better used for pyrolysis. </div><div><br></div><div>H. </div><div><br>On 2014-01-05, at 10:18 AM, Bob Stuart <<a href="mailto:bobstuart@sasktel.net">bobstuart@sasktel.net</a>> wrote:<br><br></div><blockquote type="cite"><div>
My favorite trick for lighting a wood stove is to pile up chunks of split wood so that there is an empty vertical space in the middle 2-3 cm wide. Just a bit of kindling set off in there will get the two walls radiating at each other quickly, especially if they are extra dry from being near the stove on its previous burn. A chunk on top should moderate the airflow to increase combustion temperatures until it starts to burn through. This saves me a lot of time from making and fussing over kindling. A propane torch or a bit of wax or pitch are other labor-savers.<div><br class="webkit-block-placeholder"></div><div>Bob Stuart</div><div><br><div><div>On 5-Jan-14, at 10:50 AM, Henri Naths wrote:</div><br class="Apple-interchange-newline"><blockquote type="cite"><p style="margin: 0.0px 0.0px 0.0px 0.0px"><font face="Helvetica" size="5" style="font: 16.0px Helvetica">Hi Ken</font></p> <p style="margin: 0.0px 0.0px 0.0px 0.0px"><font face="Helvetica" size="5" style="font: 16.0px Helvetica">Thank you for your good analysis of your wood stove. I know there is a better design and I'm not sure if my stove is better or not.<span class="Apple-converted-space"> </span></font></p> <p style="margin: 0.0px 0.0px 0.0px 0.0px"><font face="Helvetica" size="5" style="font: 16.0px Helvetica">Here is the thing. I burn spruce. My supply comes in 5 to 8 inch round logs dried<span class="Apple-converted-space"> </span>for ~3 years. Not sure mc but guess around 15%.-20 % I try to maintain a very hot temp so the entire logs gasify and burn over a 12 hr period. (Absolutely no fuel prep. splitting etc is mandatory lol ) It's very fickle in setting damper and air intake but for the most part I am successful. The refractory bricks helps a lot. So that is 2 burns over a 24 hr period. ( it's been averaging minus 20 c over the last two months here so not much choice)Ive run numerous test of my<span class="Apple-converted-space"> </span>theory for max efficiency under which this stove operates and settled on this operation because when the stove is shut down anywhere at the height of its max temperature and burn cycle and allowed to cool to 20 c it can be relight with a single match. <span class="Apple-converted-space"> </span></font></p> <p style="margin: 0.0px 0.0px 0.0px 0.0px"><font face="Helvetica" size="5" style="font: 16.0px Helvetica">The volatile gases including h2o could be better used for sure. They cool and condensate on the inside walls of the stove and flue before they frac. completely resulting in biochar.<span class="Apple-converted-space"> </span>The problem being the gases should be reheated, frac.ed with a catalyst and burned where the heat would be a benefit to the logs for pyrolysis.<span class="Apple-converted-space"> </span>Thus enhancing the entire burn + 20%. ( +++<span class="Apple-converted-space"> </span>considering the exponential advantage of said catalysis and resulting heat)<span class="Apple-converted-space"> </span></font></p> <p style="margin: 0.0px 0.0px 0.0px 0.0px"><font face="Helvetica" size="5" style="font: 16.0px Helvetica">A fluidized bed would also be an advantage.<span class="Apple-converted-space"> </span></font></p> <p style="margin: 0.0px 0.0px 0.0px 0.0px"><font face="Helvetica" size="5" style="font: 16.0px Helvetica"><span class="Apple-converted-space"> </span>I hope this helps.<span class="Apple-converted-space"> </span></font></p> <p style="margin: 0.0px 0.0px 0.0px 0.0px"><font face="Helvetica" size="5" style="font: 16.0px Helvetica">Yours truly<span class="Apple-converted-space"> </span></font></p> <p style="margin: 0.0px 0.0px 0.0px 0.0px"><font face="Helvetica" size="5" style="font: 16.0px Helvetica">Henri Naths</font></p> </blockquote></div><br></div></div></blockquote><blockquote type="cite"><div><span>_______________________________________________</span><br><span>Gasification mailing list</span><br><span></span><br><span>to Send a Message to the list, use the email address</span><br><span><a href="mailto:Gasification@bioenergylists.org">Gasification@bioenergylists.org</a></span><br><span></span><br><span>to UNSUBSCRIBE or Change your List Settings use the web page</span><br><span><a href="http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org">http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org</a></span><br><span></span><br><span>for more Gasifiers, News and Information see our web site:</span><br><span><a href="http://gasifiers.bioenergylists.org/">http://gasifiers.bioenergylists.org/</a></span><br></div></blockquote></body></html>