<html>
<head>
<style><!--
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
font-size: 10pt;
font-family:Tahoma
}
--></style>
</head>
<body class='hmmessage'>
Richard:  Your solution will not satisfy his wife because she made him buy a multi-head shower withsix 6 2.5 gpm showerheads. I received another inquiry from a homeowner with two back-to-back units that would draw 30 gpm. His plumber suggested a commercial boiler costing lots of money. Carmine<BR> <BR>

<HR id=stopSpelling>
Date: Sun, 15 May 2011 12:24:15 -0400<BR>Subject: Re: [Greenbuilding] low flow shower heads<BR>From: richard6@gmail.com<BR>To: gfx-ch@msn.com<BR>CC: greenbuilding@lists.bioenergylists.org; steve@tjiang.org; 9watts@gmail.com; erin@trmiles.com; sacie.lambertson@gmail.com<BR><BR>
<DIV>To start with:</DIV>
<DIV><BR></DIV>
<DIV>= Keep the 40 gallon water heater. Cost: FREE</DIV>
<DIV>= Put in a 2.5 gal/ 9 liter shower head with flow control/shutoff. Cost: ~$10 - $50. This will save him 6x his current energy cost</DIV>
<DIV>= Add an insulation blanket. Cost: ~$20 - $30</DIV>
<DIV>= Put an insulation pad underneath the water heater. Cost: ~$10</DIV>
<DIV>= Insulate any exposed water pipes. Cost: ~$10 - $25</DIV>
<DIV>= Install a 50%-DHR system. Cost: ~$700 - $1,000. In combination with the 2.5 gal. shower head this will save him 12x his current energy cost!</DIV>
<DIV><BR></DIV>
<DIV>He'll never run out of hot water with this setup unless he as some other bizarre hot water requirements. So tankless is NOT necessary. Heat loss through a tank setup is minimal if properly insulated. He will not have to upgrade his service $$$$$.</DIV>
<DIV><BR></DIV>
<DIV>I would definitely NOT recommend a tankless electric/gas water heater.</DIV>
<DIV><BR></DIV>
<DIV>Regards,</DIV>
<DIV><BR></DIV>
<DIV>Richard</DIV>
<DIV><BR></DIV><BR>=========================================================================================<BR>
<DIV class=ecxgmail_quote>On Sat, May 14, 2011 at 5:10 PM, Carmine Vasile <SPAN dir=ltr><<A href="mailto:gfx-ch@msn.com">gfx-ch@msn.com</A>></SPAN> wrote:<BR>
<BLOCKQUOTE style="BORDER-LEFT: #ccc 1px solid; PADDING-LEFT: 1ex" class=ecxgmail_quote>
<DIV>Steve, Reuben & Richard: Last week I received a call from the owner of a mult-head shower drawing 15 gpm of 105F water. He lives in North Carolina and his 40 gallon electric tank-type water heater ran out of hot water in a few minutes. I gave him my advice, install a tankless water heater with a 50%-DHR system to halve the load by recycling heat wasted down-the-drain. Solar is not an option.  <BR>   What would your advice have been?<BR>Carmine<BR><BR>Date: Fri, 13 May 2011 13:40:29 -0700<BR>From: <A href="mailto:steve@tjiang.org">steve@tjiang.org</A><BR>To: <A href="mailto:greenbuilding@lists.bioenergylists.org">greenbuilding@lists.bioenergylists.org</A><BR>Subject: Re: [Greenbuilding] low flow shower heads
<DIV class=ecxim><BR><BR>Terminology:A navy shower = turn on to wet skin; turn off to soap; turn on to rinse.A hollywood shower = turn on full blast; start singing; soap; turn off a the end.<BR><BR>A thermostatic value + volume control is  way better than a navy shower button because you can adjust the volume down to a level just to keep you warm while soaping.  This may convince more people to actually use less water while showering than the pure "Navy shower" approach.   The downside is thermostatic valves and volume controls setups are expensive.<BR></DIV><snipped> </DIV></BLOCKQUOTE></DIV><BR>                                     </body>
</html>