For a recent project we used 2" round galvalume roofing pressure plates (OMG manufacturing) and varying screw lengths to attach 1x battens.  Depending on screw length cost ranged from .25 - .34 per fastener assembly (screw and washer).  Foam layers were tacked in place with plastic cap nails.   Fasteners were purchased at a roofing supply house.  <div>
<br></div><div>Green Building Advisor has a summary for installing rigid foam insulation :</div><div><a href="http://www.greenbuildingadvisor.com/blogs/dept/musings/how-install-rigid-foam-sheathing">http://www.greenbuildingadvisor.com/blogs/dept/musings/how-install-rigid-foam-sheathing</a><br>
</div><div>With links to some videos.</div><div><br></div><div>I have used Timberlok screws but to set the head flush you have to set the screw so deep I was splitting some of the 1x battens.</div><div><br></div><div>Sam</div>
<div class="gmail_extra"><br><br><div class="gmail_quote">On Wed, Nov 14, 2012 at 11:10 PM, John Salmen <span dir="ltr"><<a href="mailto:terrain@shaw.ca" target="_blank">terrain@shaw.ca</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
When you get into long screws they are structural screws - equivalent to a<br>
3/8" bolt (actually better). For sure they are overkill but that is where<br>
eng. crosses practicality. When you increase length on anything the design<br>
requirements for actually getting the screw into the material override the<br>
design criteria for loading. The reason being that you cannot screw a long<br>
softmetal screw into an assembly without torqueing off the head. - I don't<br>
even think you can even find a #10 standard soft metal screw in long lengths<br>
anymore - I remember putting an order in from one manuf. a decade ago and<br>
half the screws were thrown away from having heads torqued off. 1/4" and<br>
3/8" lag bolts would also self destruct far too often in application to make<br>
them practical for a load that an 1/8" of metal would carry. We are talking<br>
about crews that have to install a lot of bolts/screws in a day and wasting<br>
their time with defective material is an overriding consideration.<br>
<br>
Headlok screws that I mentioned will cost about .30 per for 6" and about .50<br>
per for 8" and each screw will do what is supposed to do. They drive in<br>
quickly and perfectly each time. They have a large wafer head equivalent to<br>
a washer so one screw generally takes the place of at least 2 screws in<br>
design.<br>
<br>
Fastening is the overriding cost in assemblies at this point and it is split<br>
between the cost of the fastener and the time taken to fasten. That is why<br>
most buildings are being put together with adhesives.<br>
<div class="im"><br>
<br>
<br>
-----Original Message-----<br>
From: Greenbuilding [mailto:<a href="mailto:greenbuilding-bounces@lists.bioenergylists.org">greenbuilding-bounces@lists.bioenergylists.org</a>]<br>
</div><div><div class="h5">On Behalf Of George J. Nesbitt<br>
Sent: November-14-12 6:57 PM<br>
To: <a href="mailto:jfstraube@gmail.com">jfstraube@gmail.com</a>; Green Building<br>
Subject: Re: [Greenbuilding] Insulation fasteners<br>
<br>
I'm about to screw through 4-1/2" of polyiso, I can only find 6" screws<br>
affordably ($13/100ea), longer screws are $1ea. Sources & prices for 6"+<br>
#10 screws?<br>
<br>
On 11/14/2012 7:53 AM, John Straube wrote:<br>
> We have tested up to 8" of foam (EPS, XPS is stronger) with #10 screws and<br>
furring strips. Works fine with siding ( safety factor of more than 10).<br>
> 3/8" lags is crazy: never need it. The foam provides a lot of the<br>
strength.<br>
> Check our <a href="http://buildingscience.com" target="_blank">buildingscience.com</a> website or my book for more detail on how<br>
this works.<br>
><br>
> Sent wirelessly from my BlackBerry device on the Bell network.<br>
><br>
> -----Original Message-----<br>
> From: Clarke Olsen <<a href="mailto:colsen@fairpoint.net">colsen@fairpoint.net</a>><br>
> Sender: "Greenbuilding"<br>
> <<a href="mailto:greenbuilding-bounces@lists.bioenergylists.org">greenbuilding-bounces@lists.bioenergylists.org</a>><br>
> Date: Wed, 14 Nov 2012 09:50:23<br>
> To: Green Building<<a href="mailto:greenbuilding@lists.bioenergylists.org">greenbuilding@lists.bioenergylists.org</a>><br>
> Reply-To: Green Building <<a href="mailto:greenbuilding@lists.bioenergylists.org">greenbuilding@lists.bioenergylists.org</a>><br>
> Subject: Re: [Greenbuilding] Insulation fasteners<br>
><br></div></div><div class="im HOEnZb">
<br>
</div><div class="im HOEnZb">--<br>
George J. Nesbitt, Environmental Design / Build, Building Performance<br>
Contractor HERS I Verifier & HERS II Rater, GreenPoint Rater new & existing<br>
SF & MF, CABEC CEPE (Certified Energy Plans Examiner), Certified Passive<br>
House Consultant, BPI Multifamily Analyst, <a href="http://www.houseisasystem.com" target="_blank">www.houseisasystem.com</a>, (510)<br>
655-8532 office, <a href="tel:%28510%29%20599-5708" value="+15105995708">(510) 599-5708</a> mobile<br>
<br><br></div></blockquote></div><br>
</div>