<div dir="ltr"><div><div><div>First, a disclaimer: I am an owner-builder, so can make no claim to the economic feasibility of any building practice I have undertaken :-).  During a particularly intensive phase of my current perpetual building project, I hired a 3-man crew that actually nailed up our siding (and the framing under it).<br>
<br></div>My wife and I painted the fiber cement clapboard siding and pine trim for our house on all sides with primer and one finish coat prior to installation.  The installers whacked the cut ends with a tinted, quick drying primer as they were cut, and installed them immediately.  Fiber cement is supposed to be installed with a 1/8" gap at the ends, and filled with caulk, so the wet ends did not actually butt together.  I don't know whether this practice would be advisable with wood clapboards.<br>
<br>The pine trim we set aside just long enough for the ends to become tack-free before installation.  This primer dries quite quickly (20 minutes?), so it was not a major hassle to keep enough work going to be able to move from one location to another while pieces were drying.  We used a cheap, sacrificial paintbrush for this end painting, which we would toss at the end of the day because it became glopped up from sitting in a small, open jar of primer.<br>
<br>While we had staging installed on each side of the house, we applied a light gray caulk at end seams, nail holes, and trim seams, followed by a single finish coat of paint, for a total of one primer and two finish coats.  Because this involved only a single coat of paint, my wife and I needed only a day or so on each side to accomplish this task, before the contractor could move the staging and commence siding in a different location.<br>
<br></div>I, too, made a large painting/drying area for the clapboards, setting them on edge to dry in racks consisting of 2x4's laid on edge with big spikes nailed slightly into the edge grain every 2 inches.  The drying clapboards could lean against the spikes.  Two of us worked on the painting, with one applying the paint with a 6" roller (a roller can be loaded with a lot more paint than a brush, resulting in fewer trips to the paint), while the other smoothed it with a good quality brush.  Tedious, but pretty efficient, and it greatly diminished the painting task once the siding was installed.<br>
<br></div><div>Good luck, Reuben!<br><br></div><div>George Tremblay<br></div><div>Troy, NH<br></div></div><div class="gmail_extra"><br><br><div class="gmail_quote">On Sun, Aug 4, 2013 at 12:46 AM, Reuben Deumling <span dir="ltr"><<a href="mailto:9watts@gmail.com" target="_blank">9watts@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><div>I just stumbled upon a copy of Lstiburek's <b>Builder's Guide to Mixed Climates</b>. I was already a fan of the here recommended <b>Water Management Guide</b>, but this is pure gold.<br>
<br>
</div>I have lots of questions, but the most pressing one is how in practice you folks have gone about painting the <u>ends</u> of wooden siding boards as you cut them in the field? I'm having trouble imagining how that would work in practice. I have built large racks on which to dry painted boards, but the logistics of cutting, painting the ends, setting them aside to dry, and then returning to install those now dry pieces seem daunting. Does anyone actually do this? Are there tricks? <br>

<br><br></div>Thanks very much.<br></div>
<br>_______________________________________________<br>
Greenbuilding mailing list<br>
to Send a Message to the list, use the email address<br>
<a href="mailto:Greenbuilding@bioenergylists.org">Greenbuilding@bioenergylists.org</a><br>
<br>
to UNSUBSCRIBE or Change your List Settings use the web page<br>
<a href="http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org</a><br></blockquote>
</div><br></div>