<div dir="ltr">The 2013 California Building Code is also based on IBC but contains this modification:<div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">
2603.4.1.14 Floors. The thermal barrier specified in<br>Section 2603.4 is not required to be installed on the<br>walking surface of a structural floor system that contains<br>foam plastic insulation when the foam plastic is<br>
covered by a minimum nominal 1/2-inch-thick (12.7<br>mm) wood structural panel or approved equivalent. The<br>thermal barrier specified in Section 2603.4 is required<br>on the underside of the structural floor system that contains<br>
foam plastic insulation when the underside of the<br>structural floor system is exposed to the interior of the<br>building.</blockquote></div><div class="gmail_extra"><br clear="all"><div><div dir="ltr">Dan Johnson | <font color="#ff0000">Design and Energy</font> | 510.325.5672<span style="color:rgb(0,0,0);font-size:small"></span><div>
<font size="1">Assoc. AIA, ASHRAE, LEED AP, CEPE, CPHC | </font><span style="font-size:x-small">5500 Kales Ave. Oakland California 94618</span></div></div></div>
<br><br><div class="gmail_quote">On Wed, Apr 2, 2014 at 8:15 AM,  <span dir="ltr"><<a href="mailto:conservationarchitect@rockbridge.net" target="_blank">conservationarchitect@rockbridge.net</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Thanks for reply on EPS sealants suggestions.<br>
<br>
I am having difficulty with a code official that believes unless an assembly is referenced in the code, it is not allowed.  At issue is my proposal to float  2 layers of 7/16"osb over EPS foam.  The osb will have staggered joints and be fastened to each other with screws.  The 09 Virginia Building Code which is the same as the International Building Code states in 2603.4 Thermal Barrier over foam can be achieved with 1/2"gwb or equivalent per test protocol.   So I propose to add 1/2 gwb above foam below osb.  Because he has not seen that assembly before, he is threatening to block it because I can not find a code that explicitly describes my assembly.  With him disputing the explicit remedy describe in the code, what are my chances? $@!#^& Peace, Love<br>

<br>
Have other list participants faced similar issues with code officials regarding the thermal barrier cover over foam.<br>
<br>
Otherwise, I am interested in hearing stories of challenges we have experienced creating innovation in a code limited paradigm.<br>
<br>
Eli <br>
<br>
<br>
______________________________<u></u>_________________<br>
Greenbuilding mailing list<br>
to Send a Message to the list, use the email address<br>
<a href="mailto:Greenbuilding@bioenergylists.org" target="_blank">Greenbuilding@bioenergylists.<u></u>org</a><br>
<br>
to UNSUBSCRIBE or Change your List Settings use the web page<br>
<a href="http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org" target="_blank">http://lists.bioenergylists.<u></u>org/mailman/listinfo/<u></u>greenbuilding_lists.<u></u>bioenergylists.org</a><br>

</blockquote></div><br></div></div>