<div dir="ltr">Ever since I bought my Force 2 blower from a fellow on this list in 2005 I've wanted to find an opportunity to try that (blowing the stuff wet), but for various reasons I've never pursued that. I guess insulation ends up the least glamorous part of the remodeling jobs I do, and spending additional money on the necessary equipment hasn't seemed as tempting. I do on occasion pretend to be an insulation contractor, but I really am not. <br>But I appreciate the reminder and will take another look at what is involved. I know the Force 2 can support this, so that's a promising start.   <br></div><div class="gmail_extra"><br><div class="gmail_quote">On Wed, Mar 30, 2016 at 6:42 PM, home-nrg <span dir="ltr"><<a href="mailto:home-nrg@dnaco.net" target="_blank">home-nrg@dnaco.net</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Reuben,<br>
<br>
I'm not current on a finer mesh but a single hole and tubing<br>
the cavity makes more sense to me.<br>
<br>
Most of the contractors I have contact with are damp<br>
spraying into open cavities, then leveling to the stud face<br>
with a rotating gang brush.  Unfortunately, this requires<br>
additional equipment to inject the water into the stream of<br>
cellulose.<br>
<br>
In spite of the small amount of moisture added, I also<br>
question whether sufficient drying time is allowed before<br>
closing the walls.<br>
<br>
Bob Klahn<br>
<br>
----- Original Message Follows -----<br>
From: Reuben Deumling <<a href="mailto:9watts@gmail.com">9watts@gmail.com</a>><br>
To: Greenbuilding <<a href="mailto:greenbuilding@lists.bioenergylists.org">greenbuilding@lists.bioenergylists.org</a>><br>
Subject: [Greenbuilding] dense pack cellulose in open bays:<br>
mesh recommendations<br>
Date: Wed, 30 Mar 2016 17:08:09 -0700<br>
<div><div class="h5"><br>
> I've been doing this for a while now and have just about<br>
> used up the role of mesh (~3/16" squares?) I got about ten<br>
> years ago. Although it came recommended, I think there are<br>
> better products out there. Although by weight upwards of<br>
> 97% of the insulation blown behind (through a hole cut<br>
> into) this mesh ends up where you want it, the mess the<br>
> fine fluff makes leaking back into the room through the<br>
> mesh is really a drag. I'd love advice on whatever current<br>
> best practice is for mesh I could (presumably) glue and<br>
> staple to the studs, poke two holes per bay and blow the<br>
> stuff in good and tight.<br>
><br>
> Thanks very much.<br>
><br>
> Reuben<br>
><br>
><br>
</div></div>> _______________________________________________<br>
> Greenbuilding mailing list<br>
> to Send a Message to the list, use the email address<br>
> <a href="mailto:Greenbuilding@bioenergylists.org">Greenbuilding@bioenergylists.org</a><br>
><br>
> to UNSUBSCRIBE or Change your List Settings use the web<br>
> page<br>
><br>
<a href="http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org" rel="noreferrer" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org</a><br>
<br>
_______________________________________________<br>
Greenbuilding mailing list<br>
to Send a Message to the list, use the email address<br>
<a href="mailto:Greenbuilding@bioenergylists.org">Greenbuilding@bioenergylists.org</a><br>
<br>
to UNSUBSCRIBE or Change your List Settings use the web page<br>
<a href="http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org" rel="noreferrer" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org</a><br>
</blockquote></div><br></div>