<div dir="ltr">Thanks for your reply, Topher, and good to hear from you. This list is not quite what it once was... Have folks drifted elsewhere, and if so I wonder where those places might be?<br><br><div class="gmail_extra"><br><div class="gmail_quote">On Sat, Nov 26, 2016 at 7:03 AM, Topher Belknap <span dir="ltr"><<a href="mailto:topher@greenfret.com" target="_blank">topher@greenfret.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><br>
Greetings,<br>
<br>
Thermal losses should be considered on the basis of surface area, not<br>
volume.  </blockquote><div>Agreed.<br> <br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Heat stratification (for good or ill) is pretty insignificant in a modern, well insulated and sealed house.  </blockquote><div>I've noticed this myself and tried to discuss this with the heating man who came to advise/make a bid for the additional duct work to the new upstairs rooms), but I don't think I was able to persuade him. <br> <br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Venting ought to be the same for either option (if I am envisioning correctly).  Since it should<br>
run up the outer surface, not the interior.  </blockquote><div>I am aware that standard practice has me installing vent channels between the insulation-in-the-rafter-bays and the sheathing, that connect vents at the bottom to ridge vents--we've discussed this here over the years--but I also think I remember folks arguing that in certain situations one could skip those channels. Am I misremembering this or just experiencing wishful thinking? I confess that getting the venting right seems to me the biggest challenge at the moment. <br></div><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">My concern would be ensuring that the vapor barrier (if your climate wants one) is put in<br>
the right place.  </blockquote><div>Ah, vapor barriers. I'd love advice on this. There is currently a layer of roofing felt on the outside of the sheathing. The batts of insulation I'm planning on using for the walls and sloped roof sections of the envelope are paper-faced fiberglass. I was going to rip the paper off the batts that run vertical and keep it on the inner layer that runs horizontal. Is that a viable approach?<br></div><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">If you decide on the flat ceiling, fill that space with insulation.<br></blockquote><div>I was certainly planning on insulating above the horizontal sheet rock, but are you suggesting filling the entire triangle?  <br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<br>
Thank you kindly.<br>
<br>
Topher<br>
<br>
--<br>
Topher Belknap<br>
Green Fret Consulting<br>
Kermit didn't know the half of it...<br>
<a href="http://www.GreenFret.com/" rel="noreferrer" target="_blank">http://www.GreenFret.com/</a><br>
<br>
______________________________<wbr>_________________<br>
Greenbuilding mailing list<br>
to Send a Message to the list, use the email address<br>
<a href="mailto:Greenbuilding@bioenergylists.org">Greenbuilding@bioenergylists.<wbr>org</a><br>
<br>
to UNSUBSCRIBE or Change your List Settings use the web page<br>
<a href="http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org" rel="noreferrer" target="_blank">http://lists.bioenergylists.<wbr>org/mailman/listinfo/<wbr>greenbuilding_lists.<wbr>bioenergylists.org</a><br>
</blockquote></div><br></div></div>