[Stoves] Challenging fuel

[Ronal W. Larson]

Marquitusus, Alex, Richard,  Dr.  Nurhuda,  cc List

	1.  Alex:  I’m sure you have done some testing of this approach for using fines.  Any data to report?  (What might go wrong?,  Maximum number (or density) of “long thin plies”?, quality of the produced char?, etc)

	2.  Richard:  As our most knowledgeable expert on making briquettes (and maybe something thin like Alex is describing), am I correct in assuming that you can easily put fines into something appropriate for TLUDs?  But how coarse can that material be?    Is it relatively easy to diminish the size of something hard, as you are minimizing the dimensions of softer material in the nice videos given below?

	3.  Dr. Nurhuda:  We met at the GACC meeting in Cambodia.  Your message (not below, but on this topic) doesn’t send folk to your site for several very nice looking TLUD products available in Indonesia (and more?).   This list would benefit a lot from hearing more about your stove.  For instance, it seems that you are one of the very few separately controlling primary and secondary air.  How important is this feature?  Also I see a central structure that is not common;  does this supply some air?  Are your clients placing char in the ground?  Anything more to add about using fines, or material with a wide distribution of sizes?  More on your test results from Cambodia - that sound good.

Ron


On Dec 16, 2014, at 8:45 PM, alex english <aenglish444 at gmail.com> wrote:

> Marquitusus,
> If you first have success using your sorted or screened fuel without using the smallest pieces (the fines <3mm) in a TLUD, then you can try adding the fines
>  in a long thin pile placed like a long stick embedded in the regular fuel near the top. The fines behave a bit like a thicker piece and will 
> pyrolyse from the heat after the pyrolysis front has passed. If the fines tend to sift down to much into the regular fuel then a 2cm wide strip of
>  paper could be laid down to act as a floor for the fines. Trial and trial will show you what size of pile and how far from the bottom they 
> need to be for it to work. As long as the surrounding fuel is porous the falling pyrolysis front should proceed passing by the piles of fines.
> Gas production will vary somewhat when compared to using only optimum sized fuel, but it can still work.
> 
> Alex
> 
> On Tue, Dec 16, 2014 at 9:08 PM, Richard Stanley <rstanley at legacyfound.org> wrote:
> Marquitusus,
> 
> Here is a hand thresher-masher-chopper device we have been developing initially in collusion with a colleague in the US (Ohio) then in Guatemala and now in Nicaragua  with contributions from colleagues in Kenya and the Philippines who are developing their own versions. 
> 
> We use it for reducing and scruffing up materials for use in biomass briquette production but by removing the wire brushes you will have a simple thresher-chopper that would  nicely reduce the shells to a desired maximum size. Then, with use of a smaller size hand shaken sieve you can reduce the variation in partical size  to whatever range you desire. 
> 
> Here are two short videos showing the elements of the unit, initially  in Los Angeles California/ US, and subsequently of the unit in operation  in Cuneng, Quiche province, northern Guatemala in 2012. Our current prototype  here in Nicaragua, is about 20% cheaper and easier to build and much easier to access for cleanout but we need to really test it out  before we can claim any bragging rights..Siilar designs will also be emerging in the mentioned countries in various forms according to what resources they have available and what market needs they are responding to.  
> 
> If you like I can put you on the mailing list for the manuals which is targetted for publoication in June, 2015
> 
> kind regards,
>  Richard Stanley
> www.legacyfound.org
> 
> http://www.youtube.com/watch?v=3AJli5GFhxo
> http://www.youtube.com/watch?v=xO1plnOK4u8&feature=youtube_gdata_player=
> 
> 
> ======
> On Dec 16, 2014, at 5:21 PM, "Marquitusus " wrote:
> 
>  
> Dear stovers,
> 
> I send you a picture of the fuel I'm trying to deal with.
> This is the raw fuel as it is normally sold here. They are almond husks.
> As you see, it's sizes varies from 1 to 40mm!
> 
> Maybe people can tell me how this can affect the TLUD design
> 
>  
>  
>  
>  
> <shell-fuel.jpg>_______________________________________________
> Stoves mailing list
> 
> to Send a Message to the list, use the email address
> stoves at lists.bioenergylists.org
> 
> to UNSUBSCRIBE or Change your List Settings use the web page
> http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org
> 
> for more Biomass Cooking Stoves,  News and Information see our web site:
> http://stoves.bioenergylists.org/
> 
> 
> 
> _______________________________________________
> Stoves mailing list
> 
> to Send a Message to the list, use the email address
> stoves at lists.bioenergylists.org
> 
> to UNSUBSCRIBE or Change your List Settings use the web page
> http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org
> 
> for more Biomass Cooking Stoves,  News and Information see our web site:
> http://stoves.bioenergylists.org/
> 
> 
> _______________________________________________
> Stoves mailing list
> 
> to Send a Message to the list, use the email address
> stoves at lists.bioenergylists.org
> 
> to UNSUBSCRIBE or Change your List Settings use the web page
> http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org
> 
> for more Biomass Cooking Stoves,  News and Information see our web site:
> http://stoves.bioenergylists.org/
> 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.bioenergylists.org/pipermail/stoves_lists.bioenergylists.org/attachments/20141216/15ca0920/attachment.html>