Hi Crispin/AJH, <br><br>let me discuss some of my findings regarding to what you're saying on the hollow briquettes <br><br>When i was testing different models for the side-fed briquettes in the lab, i found out the briquette needs a little space to the wall for the air to pass through. Now if the briquette is too small (hardly pushed in the feed), it would burn unevenly, more on the top, while the hole area suffer from less draft. The distance between the briquette and the side-fed wall was around 3-5mm allaround, which makes a convenient buffer to push them in with ease. When the briquette was too tight, there was smoke coming out at sides, which was unpleasant and the briquette died many times as if this extra wall- air would help it burn more evenly and keep the fire going<br>
<br>Now, later i drilled a half-inch hole through the bottom of the combustion chamber right through the back tip of the elbow. Primarily i thought i would clean the chamber of extra ashes with pushing the stick through the hole, but i found out i never needed to do that as the briquettes would burn so well - even after 6h of making a goulash, there was no need to clean the stove even once. It would be interesting to see if this hole contributed to the fire in any way, but i never specifically tested that. <br>
<br>When you mention <i>small 3mm telltale holes could be drilled in the feed tube</i>  do you mean in the feed tube drilled vertically, so it would add up air to the side of the briquette? but when you mention the visual contact - to see the fire, i suppose you mean to drill holes horizontally in the combustion chamber itself? I think the holes in the feed-tube could be good, but they shouldn't be too big i suppose and it might contribute to an uneven burn. I tried the holes in the combustion chamber, but it didn't seem to help a lot - as you know, its difficult if not impossible to get to gasification with burning the hollow briquette like this.. <br>
<br>On the angled feed - i haven't tried that yet, but it seems tricky to make it as well as not so practical and dangerous as the briquettes might fall out while burning since they shrink a bit. So there's another mechanism needed, which i was always trying to avoid even if there's better efficiency.. <br>
<br>I did try making bigger briquettes - like 15cm diameter and firing them in a vertical position. It was pretty wild and very hard to maintain the constant heat output. It needs more effort to fire it up, but when it starts it burns like crazy with a very high flame out of the stove, while when it slows down it tends not to burn out which creates enormous amounts of CO (i was testing this at Aprovecho, specifically focusing on the latest phase of the burn - if the briquette was not burning with a solid flame, the CO went sky-high). So after this find, i really put the effort in a steady, efficient burn, which was best achieved with shorter briquettes changed regularly in the side-feed. <br>
<br>The size of the hole i ended up with was a generic hole that suited most materials and stove types. Its probably true the dimension would vary a bit with different briquette materials and stove types, but then again i don' think so much. I made briquettes with different hole diameters and different lengths, but it always showed up the hole being too big kills a fire in the chamber since there's too much cold air i suppose, or if its too small it chokes.. it would be interesting tho, to try smaller center hole and then add 'secondary' air hole to the stove somewhere but i never got into this as i was striving to at least changes to the existing stoves and briquettes and really trying to make it simple to make..<br>
<br>Anyways, a big finding was that shorter briquettes are crucial to sustain a constant fire. Besides the notion you are changing them more often, there is always a 'fresh' one in the front, controling the amount of air - feed. Like i said, when a briquette burns, it shrinks and changes the air-flow ratio. And relating to CO and usability, shorter briquettes save the fuel (you don't have to take it out and kill the flame) and limit the amount of smoke in the last phase of the burn<br>
<br>there are some more details on the site, here is a new/old link, it appears the rokstoves is broken<br><br><a href="http://mdulastove.wordpress.com/">http://mdulastove.wordpress.com/</a><br><br>Happy to contribute if i can, unfortunately don't have time nor a shop to continue working on this at the moment..<br>
<br>Greets from Vancouver, BC<br>Rok<br><br><div class="gmail_quote">On Tue, Dec 28, 2010 at 2:07 PM, Crispin Pemberton-Pigott <span dir="ltr"><<a href="mailto:crispinpigott@gmail.com">crispinpigott@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;">Dear Andrew<br>
<div class="im"><br>
>Yes Crispin but it makes my case for using a tube to separate the primary<br>
and secondary supply more intuitive.<br>
<br>
</div>I am with you on that but exploring the more radical idea of tuning the hole<br>
to the product to give correct air (maybe 100% EA) with no additional holes.<br>
I am not yet convinced that an angled gravity-infeed won't work - the way<br>
the VITA stove ran before David Hancock thought of the side feed that became<br>
the Rocket Stove. David was at Aprovecho in the old days when that inclined<br>
feed was the state of the art. The problem was the fire progressed up the<br>
fuel to the air inlet. It seems that with proper air control (which was not<br>
well understood in the early 80's) that would not have happened.<br>
<br>
So back to the past it seems: get the hole size matched to the fuel<br>
properties, then incline Rok's feed chamber and give the stove enough height<br>
to pull like crazy on the air through the hole.<br>
<br>
I don't suppose Rok has tried a nearly vertical bottom-lit briquette, has<br>
he? Something like a downdraft at maybe 60 degrees up from horizontal?<br>
<br>
If the briquette was hard enough, it may work really well.<br>
<br>
The GTZ 7.4 stove in UB was running on wood briquettes (they call them)<br>
which means a 50mm hollow log. It was working really we save for the fact<br>
they really had the fire burning in the hopper which it was NOT designed<br>
for.  I am suggesting that the air hole may be suitable for a high velocity<br>
air supply.<br>
<br>
It is probably worth my trying to run it in that mode. Hmmm...... I think I<br>
will do that maybe in February.<br>
<div class="im"><br>
>With a traditional burner all the primary air passes through the bed and if<br>
the bed is thick and hot enough no primary oxygen survives into the<br>
secondary combustion area.<br>
<br>
</div>Yes that is traditional but it is becoming a bit passé because there are<br>
just too many alternatives showing that with hard fuel (which densified wood<br>
logs are but one) it is not difficult to get secondary air past the fuel.<br>
With a hollow briquette even light density fuels are going to see this<br>
'exception' being reliable.<br>
<div class="im"><br>
>I'm simply surmising that if the amount necessary for primary combustion<br>
passes around the tube or along side the briquette and the remaining 8kg is<br>
induced up the middle of the tube then we can have primary air control for<br>
power.<br>
<br>
</div>I understand. Having tried many times I am backing off recommending central<br>
tubes in the combustion area until I see one that will survive the<br>
temperatures. Generally, if a central tube is needed, something is wrong and<br>
the tube is being inserted to overcome a problem that should not exist. When<br>
the power starts to drop, the tube kills the combustion, big time. Cecil<br>
Cook loves the idea and I think I was able to spike it with a number of<br>
demonstrations.  It is an indication of failure, basically.<br>
<div class="im"><br>
>The secondary air will be proportional to the power and largely self<br>
regulated by draught.<br>
<br>
</div>Yes, but only for a given power level. The domestic stove needs to vary both<br>
primary and secondary automatically. If you try some things, try<br>
down-drafting the secondary air with preheating like a Vesto to get that to<br>
auto-balance across perhaps a 3:1 power range. That is an achievement in<br>
itself.<br>
<div class="im"><br>
>I see Tom has chimed in with similar thoughts.<br>
<br>
</div>Tom has some ideas worth trying.<br>
<div class="im"><br>
>As I said before, if the geometry of the fire and hole can be made to do<br>
theis then great. My experience of providing all the air via the same jets<br>
</div>is it leads to high excess air, yet it does look like modern pellet burners,<br>
<div class="im">using a blast tube approach are tending that way.<br>
<br>
</div>Agreed - they are throwing the secondary past the fuel's primary burn.<br>
Simplicity when you can manage it. Imagine how difficult that would be if<br>
the secondary air was a fixed supply and the primary and fuel variable.<br>
<div class="im"><br>
>Well just a couple more: some small 3mm telltale holes could be drilled in<br>
the feed tube, they would supply some primary air but also indicate to the<br>
cook when the fire was burning back and a new briquette needs screwing in.<br>
<br>
</div>I like the vision thing. Good point. We are leaving a single hole in the<br>
ELCD stove fuel door just for looking to see how things are going. The air<br>
is definitely not needed by people complain....<br>
<br>
Holiday regards<br>
Crispin in the snow<br>
<div><div></div><div class="h5"><br>
<br>
_______________________________________________<br>
Stoves mailing list<br>
<br>
to Send a Message to the list, use the email address<br>
Stoves mailing list<br>
<br>
to UNSUBSCRIBE or Change your List Settings use the web page<br>
<a href="http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org</a><br>
<br>
for more Biomass Cooking Stoves,  News and Information see our web site:<br>
<a href="http://www.bioenergylists.org/" target="_blank">http://www.bioenergylists.org/</a><br>
<a href="mailto:Stoves@lists.bioenergylists.org">Stoves@lists.bioenergylists.org</a><br>
<a href="http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org</a><br>
</div></div></blockquote></div><br><br clear="all"><br>-- <br>Rok Oblak, MAA Design<br><br>Gregorciceva ul.5<br>4224 Gorenja vas<br>Slovenia<br><br>temporary add.:<br>305-22 E Cordova St.<br>Vancouver, BC V6A 1K2<br>Canada<br>
<br>cell: +1 604 710 1615<br><br><a href="http://www.rokstoves.com" target="_blank">www.holeyroket.com</a><br>