See comments below.<br><br><div class="gmail_quote">On Sun, Mar 4, 2012 at 4:29 PM,  <span dir="ltr"><<a href="mailto:ajheggie@gmail.com">ajheggie@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div class="im">On Sun, 4 Mar 2012 05:44:19 +0700, Paul Olivier wrote:<br>
<br>
>Someone had left a wire strainer on the floor of the university building<br>
>where I was working.<br>
>By chance the wire stainer had the same diameter as my burner housing.<br>
>When I put it over the burner and burner housing, it fit perfectly and<br>
>turned red hot.<br>
>I had never felt such heat before.<br>
><br>
>So I went to the local market and found wire strainers of finer apertures.<br>
>These worked much better than what I first tried.<br>
<br>
</div>It all sounds logical to turn a low emissivity flame to radiant heat<br>
like this and heat transfer seems the next area for big improvements<br>
with a clean burning stove.<br>
<br>
I imagine as long as the wires are kept above the autoignition point<br>
of the gases in the flame or the flame has completely burned out<br>
before touching the strainer there won't be much effect. </blockquote><div><br>I am not sure if I understand what you are saying here.<br>From what I observed, the gases have to burn below the wire mesh.<br>If they go through the wire mesh and then burn, then the wire mesh turns from red to black.<br>
Most of the gases burn close to the burner holes.<br>But there are always gases that rise in the dome and hug the underside of the dome.<br>There they burn right on the underside of the dome.<br>The wire mesh dome gives structure to the diffusion tail<br>
 and does not allow it to be so easily influenced by the random movement of air or wind.<br><br> </div><blockquote class="gmail_quote" style="margin:0pt 0pt 0pt 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
I wonder how<br>
this sits compared with the wire gauze in a Davey Safety lamp, which<br>
is there specifically to remove the source of ignition from the gases<br>
outside?<br></blockquote><div><br>Again, I do not understand your point.<br>Please clarify.<br>So sorry.<br><br>Paul Olivier<br> </div><blockquote class="gmail_quote" style="margin:0pt 0pt 0pt 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">

<br>
Have you managed to analyse the offgas before it is burnt to see if<br>
the blue flame is down to CO or just good premixing?<br>
<br>
AJH<br>
<div class="HOEnZb"><div class="h5"><br>
<br>
_______________________________________________<br>
Stoves mailing list<br>
<br>
to Send a Message to the list, use the email address<br>
<a href="mailto:stoves@lists.bioenergylists.org">stoves@lists.bioenergylists.org</a><br>
<br>
to UNSUBSCRIBE or Change your List Settings use the web page<br>
<a href="http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org</a><br>
<br>
for more Biomass Cooking Stoves,  News and Information see our web site:<br>
<a href="http://www.bioenergylists.org/" target="_blank">http://www.bioenergylists.org/</a><br>
<br>
</div></div></blockquote></div><br><br clear="all"><br>-- <br>Paul A. Olivier PhD<br>27C Pham Hong Thai Street<br>Dalat<br>Vietnam<br><br>Louisiana telephone: 1-337-447-4124 (rings Vietnam)<br>Mobile: 090-694-1573 (in Vietnam)<br>
Skype address: Xpolivier<br><a href="http://www.esrla.com/" target="_blank">http://www.esrla.com/</a><br>