<div dir="ltr"><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div>Today I ran the small pellet gasifier again.<br><a href="https://dl.dropboxusercontent.com/u/22013094/150%20Gasifier/Short/Photos/IMG_1568.JPG">https://dl.dropboxusercontent.com/u/22013094/150%20Gasifier/Short/Photos/IMG_1568.JPG</a><br>
</div>The net reactor height of this unit is only 8 inches (200 mm).<br><br></div>Here you see it in operation on rice hull pellets of a diameter of 8 mm:<br><a href="https://dl.dropboxusercontent.com/u/22013094/150%20Gasifier/Short/Photos/MVI_1574.MOV">https://dl.dropboxusercontent.com/u/22013094/150%20Gasifier/Short/Photos/MVI_1574.MOV</a><br>
</div>But in this experiment I put a layer of rice hulls on top of the pellets.<br></div>Note the beautiful blue flame.<br><br></div>I ran the same unit without the layer of rice hulls on top:<br><a href="https://dl.dropboxusercontent.com/u/22013094/150%20Gasifier/Short/Photos/MVI_1607.MOV">https://dl.dropboxusercontent.com/u/22013094/150%20Gasifier/Short/Photos/MVI_1607.MOV</a><br>
</div>Note that the flame in this case is not as blue as previously.<br></div>It seems that a layer of rice hull char helps a lot in cracking/filtering the gas.<br></div>The Pyrex pot used in this experiment was a bit too small.<br>
<br></div>There are three problems here. <br><br>The first is in lighting the pellets. We soaked some pellets in paraffin:<br><a href="https://www.dropbox.com/s/vwejx8vvu0t4kvg/IMG_1600.JPG">https://www.dropbox.com/s/vwejx8vvu0t4kvg/IMG_1600.JPG</a><br>
</div>We put these paraffin-coated pellets on top of the uncoated pellets.<br></div>Still it took too long to light the pellets.<br><br></div>We then soaked some loose rice hulls in paraffin, and put a thin layer of these paraffin-coated rice hulls on top of the pellets. This seems to work much better. When paraffin burns, it does not smell. We will now experiment with making paraffin coated wafers of a diameter of about 140 mm to place on top of the pellets. Perhaps wood pellets would not be as difficult to light as rice hull pellets.<br>
<br></div>The second problem is the size of the pellets. I would much prefer to work with pellets of a diameter of 6 mm and of a fairly uniform length. The 8 mm pellets that we were using vary in length quite a bit. Hopefully with the smaller 6 mm pellets we will not have to put a layer of rice hulls on top of the pellets to get the blue flame.<br>
<br></div>The third problem is the power of the fan. The fan that we used in this experiment has an air resistance of 0.40 InAq. This needs to be reduced to about 0.15 InAq. Such a weak fan would cost a lot less, and it would give a lot more control over flame height. The amount of electricity used with such a weak fan surely would not be greater than about 1 watt. Some might argue: then why use a fan?<br>
<br></div>We are very close here to a natural draft. But even when the reactor of a height of 8 inches is filled with only 4 inches of pellets, it does not go into natural draft mode. If the height of the reactor were extended to create natural draft conditions, a lot more heat would be loss through the wall of the reactor. Also the unit would no longer be as small and lightweight, and the cost would go up quite a bit, since I insist on using high quality stainless steel. Also in lighting the pellets, we need a lot more air than in normal operation - air that I believe only a fan could deliver. Finally a fan gives rapid and easy control over flame height and turn-down ratio.<br>
<br></div>This pellet gasifier is the same as the gasifier I designed for loose biomass, except for two things: the height of the reactor and the power of the fan. But there is a big difference in the amount of heat that the two put out. The pellet gasifier runs much hotter.<br>
<br></div>I really like the biochar that is produced by a pellet gasifier:<br><a href="https://www.dropbox.com/s/hm66yhk90x5wj7r/IMG_1610.JPG">https://www.dropbox.com/s/hm66yhk90x5wj7r/IMG_1610.JPG</a><br></div>The biochar pellets have just about the same volume as the original pellets.<br>
<br></div>Thanks.<br></div>Paul Olivier<br clear="all"><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><br>-- <br>
Paul A. Olivier PhD<br>26/5 Phu Dong Thien Vuong<br>Dalat<br>Vietnam<br>
<br>Louisiana telephone: 1-337-447-4124 (rings Vietnam)<br>Mobile: 090-694-1573 (in Vietnam)<br>Skype address: Xpolivier<br><a href="http://www.esrla.com/" target="_blank">http://www.esrla.com/</a>
</div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div>