<div dir="ltr"><div>Hi Jock and all;</div><div><br></div><div>I don't have any copper pipe around to make a gas wick, but I did find a small steel disk, so I decided to muck around with that instead, by drilling it full of holes.</div>
<div><br></div><div>The objective was to get rid of the tall conical shape of the syngas fire in a ND-TLUD and reduce soot.  I was successful at that when I cut back the primary air, but the disk may interfere with combustion if place onto a strong gas fire (if it is running a bit rich).</div>
<div><br></div><div>I have attached a pdf of photographs.</div><div><br></div><div>To say that playing with fire is in our genes is probably an understatement, because I understand that fire was domesticated by Homo erectus.</div>
<div><br></div><div>Cheers,</div><div>Julien.</div><div><br></div><div> </div></div><div class="gmail_extra"><br><br><div class="gmail_quote">On Sat, Apr 5, 2014 at 4:04 PM, Jock Gill <span dir="ltr"><<a href="mailto:jg45@icloud.com" target="_blank">jg45@icloud.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="auto"><div>Julien,</div><div><br></div><div>Thanks for pushing this experiment along.</div><div><br></div><div>
A few notes to consider inserted below.</div><div><br></div><div>Cheers,</div><div><br></div><div>Jock<br><br><div>Jock Gill</div><div>P.O. Box 3</div><div>Peacham,  VT 05862</div><div><br></div><div>Cell: <a href="tel:%28617%29%20449-8111" target="_blank" value="+16174498111">(617) 449-8111</a></div>
<div><br></div><div><span style="font-weight:bold;text-decoration:underline;background-color:rgba(255,255,255,0)"><a href="http://google.com/+JockGill" target="_blank">google.com/+JockGill</a></span></div><div><br></div><div>
<span style="background-color:rgba(255,255,255,0)">:> Extract CO2 from the atmosphere! <:</span></div><div><br></div>Via iPad</div><div><div><br>On Apr 5, 2014, at 2:46 PM, Julien Winter <<a href="mailto:winter.julien@gmail.com" target="_blank">winter.julien@gmail.com</a>> wrote:<br>
<br></div><blockquote type="cite"><div><div dir="ltr"><div>Hello Jock et al;</div><div><br></div><div>I have had a go with the two washers method, without the copper pipe in between them.  </div></div></div></blockquote><div>
<br></div></div>Are you getting flamelets yet or still flames?  In my view flamelets will give yo  cleaner results.<br><div><br></div><div>The pipe in the middle is key to improving mixing and shaping the combustion chamber.  I strongly recommend you use one.  Geometry matters.</div>
<div><br><blockquote type="cite"><div><div dir="ltr"><div>What I observed was that some of the flames came up the sides and didn't mix well.  </div></div></div></blockquote><div><br></div></div><div>See above.  Also consider:</div>
<div><br></div><div>What was the gap between the outer wall of the reactor and the edge of the disks?  Too small?  Too big? just right?</div><div><br></div><div>I find flames that creep up the wall indicates a too rich mixture -- ie not all of the fuel is consumed in the chamber.  So you might try more secondary air or less primary or both.  You only need enough primary air to establish the pyrolysis and establish a good draft in the start up phase - perhaps 10 - 12 minutes..</div>
<div><div><br></div><br><blockquote type="cite"><div><div dir="ltr"><div>So what I did was put the a concentrator lid back on (See attached photo). Now what I have is:</div>
<div><br></div><div>1) top washer in the chimney</div><div>2) concentrator disk</div><div>3) bottom washer below the secondary air jets, but above the fuel bed.</div></div></div></blockquote><blockquote type="cite"><div>
<div dir="ltr"><div><br></div><div>With the concentrator disk, the flames are forced into the middle as before, where there is mixing, but then forced apart again as they pass the upper disk. </div></div></div></blockquote>
<div><br></div></div>This could work, but I prefer a central column over a concentrator.<div><br><blockquote type="cite"><div><div dir="ltr">
<div><br></div><div>What concerns, me though is that the increased resistance to air flow has reduced the power output from the stove.</div></div></div></blockquote><div><br></div></div><div>In many cases, the dirtier the burn, the hotter the fire.  It is a fine balance to achieve a tuning that burns cleanly and delivers a reasonable amount of "power", or thermal energy, to the target.</div>
<div><br></div><div>Removing the concentrator will likely increase the draft, less resistance, and thus increase the rate of pyrolysis = increase the thermal energy output.</div><div><br><blockquote type="cite"><div><div dir="ltr">
<div><br></div><div>Tomorrow, I will run some reps with and without the gas wick gizmo to measure the rate of fuel consumption.</div></div></div></blockquote><div><br></div></div><div>I doubt this will tell you much as you will have changed far too many variables to get meaningful data.</div>
<div><br></div><div>In a day or two I will post some initial results from a FXJ burner that has ~ 12 cm disks with a 7.5 cm high combustion chamber.  No idea if this the optimal height.  The central post is about 2 inches in diameter -  a piece of steel pipe.  The reactor is 15 cm in diameter with a height of 19 cm.  I expect there may be an optimal ratio of the diameter of the center post to the diameter of the reactor.  Perhaps 1:3  Needs testing.</div>
<div><br></div><div>Keep up your experimenting and have fun too.</div><div><br></div><div>Cheers,</div><div><br></div><div>Jock</div><div><div><br></div><br><blockquote type="cite"><div><div dir="ltr">
<div><br></div><div>Cheers,</div><div>Julien<br clear="all"><br>-- <br></div><div dir="ltr">Julien Winter<br>Cobourg, ON, CANADA<br></div>
</div>
</div></blockquote></div><blockquote type="cite"><div><DSCN2215 - small.jpg></div></blockquote><blockquote type="cite"><div><span>_______________________________________________</span><br><span>Stoves mailing list</span><br>
<span></span><br><span>to Send a Message to the list, use the email address</span><br><span><a href="mailto:stoves@lists.bioenergylists.org" target="_blank">stoves@lists.bioenergylists.org</a></span><br><span></span><br><span>to UNSUBSCRIBE or Change your List Settings use the web page</span><br>
<span><a href="http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org</a></span><br><span></span><br>
<span>for more Biomass Cooking Stoves,  News and Information see our web site:</span><br><span><a href="http://stoves.bioenergylists.org/" target="_blank">http://stoves.bioenergylists.org/</a></span><br><span></span><br></div>
</blockquote></div></blockquote></div><br><br clear="all"><br>-- <br><div dir="ltr">Julien Winter<br>Cobourg, ON, CANADA<br></div>
</div>