<div dir="ltr">Hi All,<div><br></div><div>We added more bottom air until all the wood had turned to charcoal so there was no smoke at the transition.</div><div><br></div><div>Best,</div><div><br></div><div>Dean</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Fri, Dec 12, 2014 at 4:32 AM, Ray Menke <span dir="ltr"><<a href="mailto:ray.menke@gmail.com" target="_blank">ray.menke@gmail.com</a>></span> wrote:<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">If the fuel is not dry, or doesn't let enough air through, the stove<br>
will need more primary air.  A small computer fan mounted in the<br>
bottom of a tin can or 2 liter juice bottle will provide that excess<br>
air.  (I use an old motorcycle battery with clip-clip leads.)  Most of<br>
the time, it is not needed, but it does solves the problem in a hurry.<br>
It also melts grates and the walls of the burn chamber.  A sacrificial<br>
burn chamber liner from scrap metal or old stovepipe works well, and<br>
grates can be made from 1/8" thick steel.<br>
Another solution might be to mix some pencil size torrefied wood in<br>
with the almond husks.  (one or two inches in length.)  The torrefied<br>
wood is guaranteed dry, and will loosen the packing of the husks so<br>
more air can enter.<br>
My stoves are based on Paul Anderson's Champion TLUD design, and have<br>
a 2" tube at the bottom for primary air.  A funnel to direct air into<br>
the tube can be made by taping tin or cardboard around the open end of<br>
the olive can.<br>
Ray<br>
<br>
On Fri, Dec 12, 2014 at 4:57 AM, kgharris <<a href="mailto:kgharris@sonic.net">kgharris@sonic.net</a>> wrote:<br>
> Marc,<br>
><br>
> I have also been struggling with this transition problem.  It has become<br>
> more pronounced since the rains started, so humidity may be a contributing<br>
> factor.  Also, the ND-TLUD I am using has turn-down capability and the<br>
> transition problem seems to share some similarities with turn-down problems.<br>
> This makes sense because in both cases the wood gas production is being<br>
> reduced and the temperature of the flame is lower.  This made me think that<br>
> perhaps the problem could be addressed in the same way that turn-down is<br>
> addressed, with either hot char or pilot flame support.  This has so far not<br>
> worked with pilot flame support.  What has helped is giving the stove lots<br>
> of primary air to get the char hot before the flame reduces.  Entering this<br>
> phase with the stove turned to a low setting always results in smoke.  This<br>
> is in keeping with something that Crispin wrote about, using paper to cover<br>
> excess primary holes.  When the pyrolysis front reaches the bottom, it burns<br>
> the paper and lets extra primary air in to heat the char, which helps get<br>
> through this phase without smoke.  It might be a pain to add this paper to<br>
> each burn.<br>
><br>
> Fuel depth may have some input here.  With a large load the char will start<br>
> burning at the bottom and will not be near the decreasing wood gas to heat<br>
> and ignite it.  Directing air down onto the top of the char and heating some<br>
> of it to red hot may help.  This is one of the methods of supporting<br>
> turn-down by using red hot char.  Julian Winter once suggested a purched<br>
> char method for turn-down which did work.  Placing a small amount of char or<br>
> wood which will become char in a wire basket inside the reactor just below<br>
> the secondary air inlet provides red hot char to support the secondary flame<br>
> during turn-down.  This would have the deminishing transition wood-gas<br>
> passing through red hot char to be heated and ignited.  This might work for<br>
> the transition and also provide turn-down.<br>
><br>
> The primary air in this phase will be used mainly for the last bit of<br>
> pyrolysis and the char will gradually increase burning as the pyrolysis<br>
> slows down.  This produces a temperature low point before the char heats up.<br>
> Excess primary air just before this phase can heat the char to keep the<br>
> temperature up.  Keeping the temperature up is important.<br>
><br>
> Please post anything you might learn.<br>
><br>
> Kirk<br>
> Santa Rosa, CA. USA<br>
><br>
> ----- Original Message -----<br>
> From: Marquitusus<br>
> To: <a href="mailto:stoves@lists.bioenergylists.org">stoves@lists.bioenergylists.org</a><br>
> Sent: Friday, December 12, 2014 1:01 AM<br>
> Subject: [Stoves] Smokeless transition<br>
><br>
> Hi Stovers,<br>
><br>
> There is a point in the TLUD process that I find specially difficult to<br>
> understand and control: the transition from wood gasification to char<br>
> gasification. Maybe you can help me to do it.<br>
><br>
> At this point,  when the hydrocarbon fuel is near to finish, my experiments<br>
> with almond husks as fuel for ND-TLUD shows 2 possible endings:<br>
>            1- The flames in the burner turns to blue color (due to high CO<br>
> presence in gases) and the char pyrolisis continues until ashes. No smoke<br>
> present.<br>
>            2- The flames in the burner extinguishes and the smoke appears.<br>
><br>
> I made a lot of tests, with variations in ND-TLUD design (riser height,<br>
> quantity of primary and secondary air, type of concentrator, etc.)  and<br>
> still I'm not able to say which factor combination is the answer for a<br>
> smokeless transition. Sometimes I have smoke, and sometimes I don't.<br>
><br>
> I suspect the answer has to do with chemical fuel composition, as when I use<br>
> wood pellets, almost never have smoke.<br>
><br>
> So this is the point where I am today. When char gasification begins, I have<br>
> to lower the primary air? Lower the secondary air? How I can ensure the<br>
> flame won't extinguish?<br>
><br>
> It would be very useful for me to read your comments about this.<br>
><br>
> Thanks very much,<br>
><br>
> Marc<br>
><br>
><br>
> ________________________________<br>
><br>
> _______________________________________________<br>
> Stoves mailing list<br>
><br>
> to Send a Message to the list, use the email address<br>
> <a href="mailto:stoves@lists.bioenergylists.org">stoves@lists.bioenergylists.org</a><br>
><br>
> to UNSUBSCRIBE or Change your List Settings use the web page<br>
> <a href="http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org</a><br>
><br>
> for more Biomass Cooking Stoves,  News and Information see our web site:<br>
> <a href="http://stoves.bioenergylists.org/" target="_blank">http://stoves.bioenergylists.org/</a><br>
><br>
><br>
> _______________________________________________<br>
> Stoves mailing list<br>
><br>
> to Send a Message to the list, use the email address<br>
> <a href="mailto:stoves@lists.bioenergylists.org">stoves@lists.bioenergylists.org</a><br>
><br>
> to UNSUBSCRIBE or Change your List Settings use the web page<br>
> <a href="http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org</a><br>
><br>
> for more Biomass Cooking Stoves,  News and Information see our web site:<br>
> <a href="http://stoves.bioenergylists.org/" target="_blank">http://stoves.bioenergylists.org/</a><br>
><br>
><br>
<br>
<br>
<br>
--<br>
Ray  Menke<br>
<br>
_______________________________________________<br>
Stoves mailing list<br>
<br>
to Send a Message to the list, use the email address<br>
<a href="mailto:stoves@lists.bioenergylists.org">stoves@lists.bioenergylists.org</a><br>
<br>
to UNSUBSCRIBE or Change your List Settings use the web page<br>
<a href="http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org" target="_blank">http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org</a><br>
<br>
for more Biomass Cooking Stoves,  News and Information see our web site:<br>
<a href="http://stoves.bioenergylists.org/" target="_blank">http://stoves.bioenergylists.org/</a><br>
<br>
</blockquote></div></div>