<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:m="http://schemas.microsoft.com/office/2004/12/omml" xmlns="http://www.w3.org/TR/REC-html40">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=us-ascii">
<meta name="Generator" content="Microsoft Word 15 (filtered medium)">
<style><!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0cm;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
p.msonormal0, li.msonormal0, div.msonormal0
{mso-style-name:msonormal;
mso-margin-top-alt:auto;
margin-right:0cm;
mso-margin-bottom-alt:auto;
margin-left:0cm;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
span.EmailStyle19
{mso-style-type:personal-reply;
font-family:"Calibri",sans-serif;
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-size:10.0pt;}
@page WordSection1
{size:612.0pt 792.0pt;
margin:72.0pt 72.0pt 72.0pt 72.0pt;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext="edit" spidmax="1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext="edit">
<o:idmap v:ext="edit" data="1" />
</o:shapelayout></xml><![endif]-->
</head>
<body lang="EN-CA" link="blue" vlink="purple">
<div class="WordSection1">
<p class="MsoNormal"><span style="mso-fareast-language:EN-US">I don’t see a gap. Or are you just showing is the two diameters?<o:p></o:p></span></p>
<p class="MsoNormal"><span style="mso-fareast-language:EN-US"><o:p> </o:p></span></p>
<p class="MsoNormal"><span style="mso-fareast-language:EN-US">The gap is 63 cm2 which is about a 90mm diameter hole. That is plenty big.<o:p></o:p></span></p>
<p class="MsoNormal"><span style="mso-fareast-language:EN-US">I’ll bet you can cut it in half. Try a disk of 140mm. Cut it 145 and hammer the edge over to make a small radius of about 3mm instead of having a sharp edge. It will increase the velocity without
costing you much in terms of draft.<o:p></o:p></span></p>
<p class="MsoNormal"><span style="mso-fareast-language:EN-US"><o:p> </o:p></span></p>
<p class="MsoNormal"><span style="mso-fareast-language:EN-US">Regards<o:p></o:p></span></p>
<p class="MsoNormal"><span style="mso-fareast-language:EN-US">Crispin<o:p></o:p></span></p>
<p class="MsoNormal"><span style="mso-fareast-language:EN-US"><o:p> </o:p></span></p>
<div>
<div style="border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0cm 0cm 0cm">
<p class="MsoNormal"><b><span lang="EN-US">From:</span></b><span lang="EN-US"> Stoves [mailto:stoves-bounces@lists.bioenergylists.org]
<b>On Behalf Of </b>Jock Gill<br>
<b>Sent:</b> 27-Sep-17 13:57<br>
<b>To:</b> stoves@lists.bioenergylists.org<br>
<b>Subject:</b> [Stoves] Addendum: 64% coverage<o:p></o:p></span></p>
</div>
</div>
<p class="MsoNormal"><o:p> </o:p></p>
<div>
<div>
<p class="MsoNormal" style="margin-bottom:12.0pt"><span style="font-size:10.0pt">This shows the relationship of the 12 cm diameter disk to the 15 cm diameter pyrolysis surface. It also illustrates the relative size of the gap the pyrolysis gases must pass through
to enter the combustion chamber<o:p></o:p></span></p>
<p class="MsoNormal" style="margin-bottom:12.0pt"><o:p> </o:p></p>
</div>
</div>
</div>
</body>
</html>