[Gasification] Regarding Combustion Quality of Producer gas

Thomas Reed tombreed2010 at gmail.com
Fri Oct 12 17:15:20 CDT 2012


Dear Greg and all

Producer gas from wood tends to contain 21% CO as well as 19% H2 (And ~ 4%methane, CH4).

 The heat of combustion of both is about 270 BTU/scf, so don't forget or downgrade the CO content. CO has the lowest flame velocity of any fuel gas, but H2 is about 5X most other gases, so  the combination of H2, CO and CH4 (1,000 Btu/acf) burns reasonably well (but don't breathe too much of it).  

<><><>

"Octane" is a measure of the degree to which a gas-air mixture  can be compressed before it pre-ignites.   Typically the CR of gasoline is ~ 9/1, and the Octane is ~ 90, and in general required octane = 10X CR.  

The power and efficiency of IC engines is directly proportional to CR and hence to octane.  

 With 50% N2, the octane of producer gas is around 180!  So you can increase the CR of engines using PG to 18/1 and double the power and efficiency.  

<><><>

Modern engines use knock sensors/timing to increase combustion efficiency by operating just below the knock limit.  I presume that this would greatly increase power and efficiency of PG, but I don't know if they could increase CR enough to accomodate PG.

Opinions?  

Onward...

Tom Reed 


On Oct 11, 2012, at 6:46 AM, Greg Manning <a31ford at gmail.com> wrote:

> Greetings Vikrant,
>  
> Generally, when talking about the quality of producer gas (PG) we talk of the percentage of Hydrogen (H2), natural air driven systems range from 6% H2, to good quality systems that produce upwards of 30% H2 content.
>  
> If one moves to a oxygen based system (SG) Synthisis Gas, the H2 content pushes the 60% and up level, If one moves to externally driven systems, I am told they are even higher than that.
> <><><>



> 
> Greg Manning
> Canadian Gasifier Ltd.
>  
>  
> On Thu, Oct 11, 2012 at 1:51 AM, vikrant bhalerao <vikrantbhalerao12 at gmail.com> wrote:
>> Hi,
>>  
>> I have a question regarding combustion quality of PG.
>> When we talk about natural gas, in short 'Methane index/Methane Number' provide combustion quality. For gasolin/petrol it is 'octane rating'. Can we use 'Methane number' as indicator for PG also ??
>>  
>> Thanks
>> With Regards,
>> Vikrant Bhalerao
>> Cummins India Ltd.
>> Mobile +91 89 833 20 725
>>  
>> 
>> 
>> 
>> On Thu, Oct 11, 2012 at 12:30 AM, <gasification-request at lists.bioenergylists.org> wrote:
>>> Send Gasification mailing list submissions to
>>>         gasification at lists.bioenergylists.org
>>> 
>>> To subscribe or unsubscribe via the World Wide Web, visit
>>>         http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> 
>>> or, via email, send a message with subject or body 'help' to
>>>         gasification-request at lists.bioenergylists.org
>>> 
>>> You can reach the person managing the list at
>>>         gasification-owner at lists.bioenergylists.org
>>> 
>>> When replying, please edit your Subject line so it is more specific
>>> than "Re: Contents of Gasification digest..."
>>> 
>>> 
>>> Today's Topics:
>>> 
>>>    1. Small scale power plants? (Kenny Redd)
>>>    2. Small scale power plants? (doug.williams)
>>>    3. Small scale power plants? (doug.williams)
>>>    4. Gasification of Corn cob (masi karuppu)
>>>    5. Re: Gasification of Corn cob (Thomas Reed)
>>>    6. Re: Small scale power plants? (Thomas Reed)
>>>    7. Re: Small scale power plants? (Thomas Reed)
>>>    8. Re: Gasification of Corn cob (Darius)
>>>    9. Re: Small scale power plants? (Kenny Redd)
>>>   10. Re: Small scale power plants? (Kenny Redd)
>>>   11. Re: Small scale power plants? (Phil Marsh)
>>>   12. Re: Gasification of Corn cob (Kevin)
>>> 
>>> 
>>> ----------------------------------------------------------------------
>>> 
>>> Message: 1
>>> Date: Tue, 9 Oct 2012 22:42:28 -0500
>>> From: Kenny Redd <kenredd at gmail.com>
>>> To: Gasification at bioenergylists.org
>>> Subject: [Gasification] Small scale power plants?
>>> Message-ID:
>>>         <CAD9Lsq5hEUS4tV2d-NLXy7RG+ZBrmSPu_EaeH18Mf-m3Vyokeg at mail.gmail.com>
>>> Content-Type: text/plain; charset="iso-8859-1"
>>> 
>>> I tip my hat to bioenergylists.org
>>> 
>>> Is anyone aware of a US commercial producer of small-scale, solid-fuel
>>> (bio-coal fired) power plants in the 1 to 20 MW range?
>>> 
>>> Thanks for all assistance.
>>> 
>>> Kenny Redd
>>> Inova Energy LLC
>>> -------------- next part --------------
>>> An HTML attachment was scrubbed...
>>> URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121009/44b2020f/attachment-0001.html>
>>> 
>>> ------------------------------
>>> 
>>> Message: 2
>>> Date: Wed, 10 Oct 2012 18:35:51 +1300
>>> From: "doug.williams" <Doug.Williams at orcon.net.nz>
>>> To: "Discussion of biomass pyrolysis and gasification"
>>>         <gasification at lists.bioenergylists.org>,
>>>         <Gasification at bioenergylists.org>
>>> Subject: [Gasification] Small scale power plants?
>>> Message-ID: <84694C38CDD54725928D1713D37DE21F at dougspc>
>>> Content-Type: text/plain; charset="iso-8859-1"
>>> 
>>> Hi Kenny,
>>> 
>>> You ask:
>>> 
>>> Is anyone aware of a US commercial producer of small-scale, solid-fuel (bio-coal fired) power plants in the 1 to 20 MW range?
>>> 
>>> Please define your version of bio-coal, as it can have differing interpretations. It suggests charcoal, if so, one might expect for you to consider a number of options. Tell us more. because there is a huge gap between raw and "pre-charred" fuel gasification. Your range of outputs stretch credibility to supply a pre-carbonized fuel for 20MWe, so what is the direction of your enquiry?  Possibly you are researching the capabilities of the technology, but 1-20MWe is rather big when discussing biomass gasification systems. You might also comment on the end use of the gas, boiler of engine power generation?
>>> 
>>> This forum has an affinity with discussing these issues, because the future needs what we may be able to do, given the right challenges, and your question should trigger off comment from the accumulated expertise.
>>> 
>>> Doug Williams,
>>> Fluidyne.
>>> -------------- next part --------------
>>> An HTML attachment was scrubbed...
>>> URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121010/18ff77af/attachment-0002.html>
>>> 
>>> ------------------------------
>>> 
>>> Message: 3
>>> Date: Wed, 10 Oct 2012 18:35:51 +1300
>>> From: "doug.williams" <Doug.Williams at orcon.net.nz>
>>> To: "Discussion of biomass pyrolysis and gasification"
>>>         <gasification at lists.bioenergylists.org>,
>>>         <Gasification at bioenergylists.org>
>>> Subject: [Gasification] Small scale power plants?
>>> Message-ID: <84694C38CDD54725928D1713D37DE21F at dougspc>
>>> Content-Type: text/plain; charset="iso-8859-1"
>>> 
>>> Hi Kenny,
>>> 
>>> You ask:
>>> 
>>> Is anyone aware of a US commercial producer of small-scale, solid-fuel (bio-coal fired) power plants in the 1 to 20 MW range?
>>> 
>>> Please define your version of bio-coal, as it can have differing interpretations. It suggests charcoal, if so, one might expect for you to consider a number of options. Tell us more. because there is a huge gap between raw and "pre-charred" fuel gasification. Your range of outputs stretch credibility to supply a pre-carbonized fuel for 20MWe, so what is the direction of your enquiry?  Possibly you are researching the capabilities of the technology, but 1-20MWe is rather big when discussing biomass gasification systems. You might also comment on the end use of the gas, boiler of engine power generation?
>>> 
>>> This forum has an affinity with discussing these issues, because the future needs what we may be able to do, given the right challenges, and your question should trigger off comment from the accumulated expertise.
>>> 
>>> Doug Williams,
>>> Fluidyne.
>>> -------------- next part --------------
>>> An HTML attachment was scrubbed...
>>> URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121010/18ff77af/attachment-0003.html>
>>> 
>>> ------------------------------
>>> 
>>> Message: 4
>>> Date: Wed, 10 Oct 2012 14:32:43 +0530
>>> From: masi karuppu <masikaruppu at gmail.com>
>>> To: Gasification at bioenergylists.org
>>> Subject: [Gasification] Gasification of Corn cob
>>> Message-ID:
>>>         <CAEDEmzDtssbbL7VHdr7GKgruuYWrfK9DaXRhbCcoegvyxnhYhw at mail.gmail.com>
>>> Content-Type: text/plain; charset=ISO-8859-1
>>> 
>>> Dear Sir,
>>> 
>>> I would like to know about the operating performance of a gasifier
>>> which works on Corn cob as fuel input.
>>> 
>>> Thanks and regards
>>> K.Subramaniam
>>> 
>>> 
>>> 
>>> ------------------------------
>>> 
>>> Message: 5
>>> Date: Wed, 10 Oct 2012 09:19:35 -0400
>>> From: Thomas Reed <tombreed2010 at gmail.com>
>>> To: Discussion of biomass pyrolysis and gasification
>>>         <gasification at lists.bioenergylists.org>
>>> Subject: Re: [Gasification] Gasification of Corn cob
>>> Message-ID: <BA4B42AD-C053-4789-98F9-AD38EF8B236F at gmail.com>
>>> Content-Type: text/plain;       charset=us-ascii
>>> 
>>> Dear Masi
>>> 
>>> I have never run a gasifier on corn cobs, but I believe they would be an excellent fuel as long as the moisture content is <15%. Be sure to operate lighting the TOP of the pile so that the char sits above the unburned fuel.
>>> 
>>> Write me -send a picture- if you can.
>>> 
>>> Yours truly,
>>> 
>>> Tom Reed
>>> 
>>> Thomas B Reed
>>> 
>>> 
>>> On Oct 10, 2012, at 5:02 AM, masi karuppu <masikaruppu at gmail.com> wrote:
>>> 
>>> > Dear Sir,
>>> >
>>> > I would like to know about the operating performance of a gasifier
>>> > which works on Corn cob as fuel input.
>>> >
>>> > Thanks and regards
>>> > K.Subramaniam
>>> >
>>> > _______________________________________________
>>> > Gasification mailing list
>>> >
>>> > to Send a Message to the list, use the email address
>>> > Gasification at bioenergylists.org
>>> >
>>> > to UNSUBSCRIBE or Change your List Settings use the web page
>>> > http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> >
>>> > for more Gasifiers,  News and Information see our web site:
>>> > http://gasifiers.bioenergylists.org/
>>> 
>>> 
>>> 
>>> ------------------------------
>>> 
>>> Message: 6
>>> Date: Wed, 10 Oct 2012 09:22:45 -0400
>>> From: Thomas Reed <tombreed2010 at gmail.com>
>>> To: "doug.williams" <Doug.Williams at orcon.net.nz>,       Discussion of
>>>         biomass pyrolysis and gasification
>>>         <gasification at lists.bioenergylists.org>
>>> Cc: Discussion of biomass pyrolysis and gasification
>>>         <gasification at lists.bioenergylists.org>,
>>>         "<Gasification at bioenergylists.org>" <Gasification at bioenergylists.org>
>>> Subject: Re: [Gasification] Small scale power plants?
>>> Message-ID: <4BD28B36-55AE-4619-B1C3-DA40AD77AF2F at gmail.com>
>>> Content-Type: text/plain; charset="us-ascii"
>>> 
>>> Biocoal isNOT charcoal!  It contains 80% of the energy in the original wood, but is friable, easily compressed, briquettes or fired as a powder in utility boilers by itself or as an aid to better combustion of powdered coal.
>>> 
>>> Tom Reed
>>> 
>>> Thomas B Reed
>>> 
>>> 
>>> On Oct 10, 2012, at 1:35 AM, "doug.williams" <Doug.Williams at orcon.net.nz> wrote:
>>> 
>>> > Hi Kenny,
>>> >
>>> > You ask:
>>> >
>>> > Is anyone aware of a US commercial producer of small-scale, solid-fuel (bio-coal fired) power plants in the 1 to 20 MW range?
>>> >
>>> > Please define your version of bio-coal, as it can have differing interpretations. It suggests charcoal, if so, one might expect for you to consider a number of options. Tell us more. because there is a huge gap between raw and "pre-charred" fuel gasification. Your range of outputs stretch credibility to supply a pre-carbonized fuel for 20MWe, so what is the direction of your enquiry?  Possibly you are researching the capabilities of the technology, but 1-20MWe is rather big when discussing biomass gasification systems. You might also comment on the end use of the gas, boiler of engine power generation?
>>> >
>>> > This forum has an affinity with discussing these issues, because the future needs what we may be able to do, given the right challenges, and your question should trigger off comment from the accumulated expertise.
>>> >
>>> > Doug Williams,
>>> > Fluidyne.
>>> > _______________________________________________
>>> > Gasification mailing list
>>> >
>>> > to Send a Message to the list, use the email address
>>> > Gasification at bioenergylists.org
>>> >
>>> > to UNSUBSCRIBE or Change your List Settings use the web page
>>> > http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> >
>>> > for more Gasifiers,  News and Information see our web site:
>>> > http://gasifiers.bioenergylists.org/
>>> -------------- next part --------------
>>> An HTML attachment was scrubbed...
>>> URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121010/a87f66c5/attachment-0002.html>
>>> 
>>> ------------------------------
>>> 
>>> Message: 7
>>> Date: Wed, 10 Oct 2012 09:22:45 -0400
>>> From: Thomas Reed <tombreed2010 at gmail.com>
>>> To: "doug.williams" <Doug.Williams at orcon.net.nz>,       Discussion of
>>>         biomass pyrolysis and gasification
>>>         <gasification at lists.bioenergylists.org>
>>> Cc: Discussion of biomass pyrolysis and gasification
>>>         <gasification at lists.bioenergylists.org>,
>>>         "<Gasification at bioenergylists.org>" <Gasification at bioenergylists.org>
>>> Subject: Re: [Gasification] Small scale power plants?
>>> Message-ID: <4BD28B36-55AE-4619-B1C3-DA40AD77AF2F at gmail.com>
>>> Content-Type: text/plain; charset="us-ascii"
>>> 
>>> Biocoal isNOT charcoal!  It contains 80% of the energy in the original wood, but is friable, easily compressed, briquettes or fired as a powder in utility boilers by itself or as an aid to better combustion of powdered coal.
>>> 
>>> Tom Reed
>>> 
>>> Thomas B Reed
>>> 
>>> 
>>> On Oct 10, 2012, at 1:35 AM, "doug.williams" <Doug.Williams at orcon.net.nz> wrote:
>>> 
>>> > Hi Kenny,
>>> >
>>> > You ask:
>>> >
>>> > Is anyone aware of a US commercial producer of small-scale, solid-fuel (bio-coal fired) power plants in the 1 to 20 MW range?
>>> >
>>> > Please define your version of bio-coal, as it can have differing interpretations. It suggests charcoal, if so, one might expect for you to consider a number of options. Tell us more. because there is a huge gap between raw and "pre-charred" fuel gasification. Your range of outputs stretch credibility to supply a pre-carbonized fuel for 20MWe, so what is the direction of your enquiry?  Possibly you are researching the capabilities of the technology, but 1-20MWe is rather big when discussing biomass gasification systems. You might also comment on the end use of the gas, boiler of engine power generation?
>>> >
>>> > This forum has an affinity with discussing these issues, because the future needs what we may be able to do, given the right challenges, and your question should trigger off comment from the accumulated expertise.
>>> >
>>> > Doug Williams,
>>> > Fluidyne.
>>> > _______________________________________________
>>> > Gasification mailing list
>>> >
>>> > to Send a Message to the list, use the email address
>>> > Gasification at bioenergylists.org
>>> >
>>> > to UNSUBSCRIBE or Change your List Settings use the web page
>>> > http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> >
>>> > for more Gasifiers,  News and Information see our web site:
>>> > http://gasifiers.bioenergylists.org/
>>> -------------- next part --------------
>>> An HTML attachment was scrubbed...
>>> URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121010/a87f66c5/attachment-0003.html>
>>> 
>>> ------------------------------
>>> 
>>> Message: 8
>>> Date: Wed, 10 Oct 2012 20:14:19 +0700
>>> From: Darius <darius_tamizi at hotmail.com>
>>> To: Discussion of biomass pyrolysis and gasification
>>>         <gasification at lists.bioenergylists.org>
>>> Subject: Re: [Gasification] Gasification of Corn cob
>>> Message-ID: <BLU0-SMTP1115A4D5FC27DBA64823C4E8A8E0 at phx.gbl>
>>> Content-Type: text/plain; charset="ISO-8859-1"; format=flowed
>>> 
>>> As long as the corb is dry, it produce almost the same gas quality as
>>> wood, but you need to add the corb 2 times more quick than wood.
>>> 
>>> Regards,
>>> 
>>> Darius
>>> 
>>>   On 10/10/2012 8:19 PM, Thomas Reed wrote:
>>> > Dear Masi
>>> >
>>> > I have never run a gasifier on corn cobs, but I believe they would be an excellent fuel as long as the moisture content is <15%. Be sure to operate lighting the TOP of the pile so that the char sits above the unburned fuel.
>>> >
>>> > Write me -send a picture- if you can.
>>> >
>>> > Yours truly,
>>> >
>>> > Tom Reed
>>> >
>>> > Thomas B Reed
>>> >
>>> >
>>> > On Oct 10, 2012, at 5:02 AM, masi karuppu <masikaruppu at gmail.com> wrote:
>>> >
>>> >> Dear Sir,
>>> >>
>>> >> I would like to know about the operating performance of a gasifier
>>> >> which works on Corn cob as fuel input.
>>> >>
>>> >> Thanks and regards
>>> >> K.Subramaniam
>>> >>
>>> >> _______________________________________________
>>> >> Gasification mailing list
>>> >>
>>> >> to Send a Message to the list, use the email address
>>> >> Gasification at bioenergylists.org
>>> >>
>>> >> to UNSUBSCRIBE or Change your List Settings use the web page
>>> >> http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> >>
>>> >> for more Gasifiers,  News and Information see our web site:
>>> >> http://gasifiers.bioenergylists.org/
>>> > _______________________________________________
>>> > Gasification mailing list
>>> >
>>> > to Send a Message to the list, use the email address
>>> > Gasification at bioenergylists.org
>>> >
>>> > to UNSUBSCRIBE or Change your List Settings use the web page
>>> > http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> >
>>> > for more Gasifiers,  News and Information see our web site:
>>> > http://gasifiers.bioenergylists.org/
>>> >
>>> >
>>> 
>>> 
>>> 
>>> 
>>> ------------------------------
>>> 
>>> Message: 9
>>> Date: Wed, 10 Oct 2012 09:34:02 -0500
>>> From: Kenny Redd <kenredd at gmail.com>
>>> To: "doug.williams" <Doug.Williams at orcon.net.nz>,       Discussion of
>>>         biomass pyrolysis and gasification
>>>         <gasification at lists.bioenergylists.org>
>>> Subject: Re: [Gasification] Small scale power plants?
>>> Message-ID:
>>>         <CAD9Lsq6Jnf3OprF=QAP6=HpCf9AmNO3CCey=dj9OX2DHYu4yhw at mail.gmail.com>
>>> Content-Type: text/plain; charset="iso-8859-1"
>>> 
>>> Thanks Doug and Tom for responding to my inquiry,
>>> 
>>> A little clarity is in order.  I am a designer for an R&D company that
>>> tends to contract to Federal agencies.  I have discussions with top level
>>> decision makers within the company.  I have pointed out the US Army's seven
>>> billion dollar energy acqusition program and have suggested that my
>>> employer consider a Power Producing Agreement (PPA) with the Army.  I have
>>> suggested that Federal lands provide the space for biofuel crops.  These
>>> crops would ultimately be converted via pyrolysis to a coal surrogate that
>>> can be handled like fossil coal.  However, the PPA power would likely have
>>> to be distributed in a decentralized, on-site fashion and on a scale much
>>> smaller than the typical gigawatt power plant.
>>> 
>>> It's not my interest to employ gasification as the fuel product, but as
>>> part of the process to produce a transportable, exportable, friable, solid
>>> fuel from the feedstocks.  My review of the gasification industry shows
>>> that the technology for producing the "bio-coal" is mature and readily
>>> available.  However, it doesn't appear there are small scale, power-plants
>>> suitable for on-site power production.  Any suggestions?
>>> 
>>> Thanks again, and Bioenergylists is one of the best forums on the web.
>>> 
>>> 
>>> 
>>> 
>>> On Wed, Oct 10, 2012 at 12:35 AM, doug.williams
>>> <Doug.Williams at orcon.net.nz>wrote:
>>> 
>>> > **
>>> > *Hi Kenny,*
>>> > **
>>> > *You ask*:
>>> >
>>> > Is anyone aware of a US commercial producer of small-scale, solid-fuel
>>> > (bio-coal fired) power plants in the 1 to 20 MW range?
>>> >
>>> > *Please define your version of bio-coal, as it can have differing
>>> > interpretations. It suggests charcoal, if so, one might expect for you to
>>> > consider a number of options. **Tell us more. because there is a huge gap
>>> > between raw and "pre-charred" fuel gasification. Your range of outputs
>>> > stretch credibility to supply a pre-carbonized fuel for 20MWe, so what is
>>> > the direction of your enquiry?  Possibly you are researching the
>>> > capabilities of the technology, but 1-20MWe is rather big when discussing
>>> > biomass gasification systems. You might also comment on the end use of the
>>> > gas, boiler of engine power generation? *
>>> > **
>>> > *This forum has an affinity with discussing these issues, because the
>>> > future needs what we may be able to do, given the right challenges, and
>>> > your question should trigger off comment from the accumulated expertise.*
>>> > **
>>> > *Doug Williams,*
>>> > *Fluidyne.*
>>> >
>>> > _______________________________________________
>>> > Gasification mailing list
>>> >
>>> > to Send a Message to the list, use the email address
>>> > Gasification at bioenergylists.org
>>> >
>>> > to UNSUBSCRIBE or Change your List Settings use the web page
>>> >
>>> > http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> >
>>> > for more Gasifiers,  News and Information see our web site:
>>> > http://gasifiers.bioenergylists.org/
>>> >
>>> >
>>> -------------- next part --------------
>>> An HTML attachment was scrubbed...
>>> URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121010/1db7c8e1/attachment-0002.html>
>>> 
>>> ------------------------------
>>> 
>>> Message: 10
>>> Date: Wed, 10 Oct 2012 09:34:02 -0500
>>> From: Kenny Redd <kenredd at gmail.com>
>>> To: "doug.williams" <Doug.Williams at orcon.net.nz>,       Discussion of
>>>         biomass pyrolysis and gasification
>>>         <gasification at lists.bioenergylists.org>
>>> Subject: Re: [Gasification] Small scale power plants?
>>> Message-ID:
>>>         <CAD9Lsq6Jnf3OprF=QAP6=HpCf9AmNO3CCey=dj9OX2DHYu4yhw at mail.gmail.com>
>>> Content-Type: text/plain; charset="iso-8859-1"
>>> 
>>> Thanks Doug and Tom for responding to my inquiry,
>>> 
>>> A little clarity is in order.  I am a designer for an R&D company that
>>> tends to contract to Federal agencies.  I have discussions with top level
>>> decision makers within the company.  I have pointed out the US Army's seven
>>> billion dollar energy acqusition program and have suggested that my
>>> employer consider a Power Producing Agreement (PPA) with the Army.  I have
>>> suggested that Federal lands provide the space for biofuel crops.  These
>>> crops would ultimately be converted via pyrolysis to a coal surrogate that
>>> can be handled like fossil coal.  However, the PPA power would likely have
>>> to be distributed in a decentralized, on-site fashion and on a scale much
>>> smaller than the typical gigawatt power plant.
>>> 
>>> It's not my interest to employ gasification as the fuel product, but as
>>> part of the process to produce a transportable, exportable, friable, solid
>>> fuel from the feedstocks.  My review of the gasification industry shows
>>> that the technology for producing the "bio-coal" is mature and readily
>>> available.  However, it doesn't appear there are small scale, power-plants
>>> suitable for on-site power production.  Any suggestions?
>>> 
>>> Thanks again, and Bioenergylists is one of the best forums on the web.
>>> 
>>> 
>>> 
>>> 
>>> On Wed, Oct 10, 2012 at 12:35 AM, doug.williams
>>> <Doug.Williams at orcon.net.nz>wrote:
>>> 
>>> > **
>>> > *Hi Kenny,*
>>> > **
>>> > *You ask*:
>>> >
>>> > Is anyone aware of a US commercial producer of small-scale, solid-fuel
>>> > (bio-coal fired) power plants in the 1 to 20 MW range?
>>> >
>>> > *Please define your version of bio-coal, as it can have differing
>>> > interpretations. It suggests charcoal, if so, one might expect for you to
>>> > consider a number of options. **Tell us more. because there is a huge gap
>>> > between raw and "pre-charred" fuel gasification. Your range of outputs
>>> > stretch credibility to supply a pre-carbonized fuel for 20MWe, so what is
>>> > the direction of your enquiry?  Possibly you are researching the
>>> > capabilities of the technology, but 1-20MWe is rather big when discussing
>>> > biomass gasification systems. You might also comment on the end use of the
>>> > gas, boiler of engine power generation? *
>>> > **
>>> > *This forum has an affinity with discussing these issues, because the
>>> > future needs what we may be able to do, given the right challenges, and
>>> > your question should trigger off comment from the accumulated expertise.*
>>> > **
>>> > *Doug Williams,*
>>> > *Fluidyne.*
>>> >
>>> > _______________________________________________
>>> > Gasification mailing list
>>> >
>>> > to Send a Message to the list, use the email address
>>> > Gasification at bioenergylists.org
>>> >
>>> > to UNSUBSCRIBE or Change your List Settings use the web page
>>> >
>>> > http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> >
>>> > for more Gasifiers,  News and Information see our web site:
>>> > http://gasifiers.bioenergylists.org/
>>> >
>>> >
>>> -------------- next part --------------
>>> An HTML attachment was scrubbed...
>>> URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121010/1db7c8e1/attachment-0003.html>
>>> 
>>> ------------------------------
>>> 
>>> Message: 11
>>> Date: Wed, 10 Oct 2012 07:37:21 -0700
>>> From: "Phil Marsh" <marshbros at mcbridebc.com>
>>> To: "'Discussion of biomass pyrolysis and gasification'"
>>>         <gasification at lists.bioenergylists.org>
>>> Subject: Re: [Gasification] Small scale power plants?
>>> Message-ID: <000001cda6f4$c21094b0$4631be10$@com>
>>> Content-Type: text/plain; charset="utf-8"
>>> 
>>> Dear Dr. Reed:
>>> 
>>> 
>>> 
>>> Why is charcoal not just a specific type of biocoal? (as in biocoal made from wood) Or are you specifically  saying biocoal is a term only used to describe a product that is torrefied as opposed to fully carbonized as a standard version of charcoal would be?
>>> 
>>> 
>>> 
>>> Phil Marsh
>>> 
>>> Marshbros.
>>> 
>>> 250 569-7858
>>> 
>>> 
>>> 
>>> From: Gasification [mailto:gasification-bounces at lists.bioenergylists.org] On Behalf Of Thomas Reed
>>> Sent: October-10-12 6:23 AM
>>> To: doug.williams; Discussion of biomass pyrolysis and gasification
>>> Cc: Discussion of biomass pyrolysis and gasification; <Gasification at bioenergylists.org>
>>> Subject: Re: [Gasification] Small scale power plants?
>>> 
>>> 
>>> 
>>> Biocoal isNOT charcoal!  It contains 80% of the energy in the original wood, but is friable, easily compressed, briquettes or fired as a powder in utility boilers by itself or as an aid to better combustion of powdered coal.
>>> 
>>> 
>>> 
>>> Tom Reed
>>> 
>>> Thomas B Reed
>>> 
>>> 
>>> 
>>> 
>>> 
>>> 
>>> On Oct 10, 2012, at 1:35 AM, "doug.williams" <Doug.Williams at orcon.net.nz> wrote:
>>> 
>>> Hi Kenny,
>>> 
>>> 
>>> 
>>> You ask:
>>> 
>>> 
>>> Is anyone aware of a US commercial producer of small-scale, solid-fuel (bio-coal fired) power plants in the 1 to 20 MW range?
>>> 
>>> Please define your version of bio-coal, as it can have differing interpretations. It suggests charcoal, if so, one might expect for you to consider a number of options. Tell us more. because there is a huge gap between raw and "pre-charred" fuel gasification. Your range of outputs stretch credibility to supply a pre-carbonized fuel for 20MWe, so what is the direction of your enquiry?  Possibly you are researching the capabilities of the technology, but 1-20MWe is rather big when discussing biomass gasification systems. You might also comment on the end use of the gas, boiler of engine power generation?
>>> 
>>> 
>>> 
>>> This forum has an affinity with discussing these issues, because the future needs what we may be able to do, given the right challenges, and your question should trigger off comment from the accumulated expertise.
>>> 
>>> 
>>> 
>>> Doug Williams,
>>> 
>>> Fluidyne.
>>> 
>>> _______________________________________________
>>> Gasification mailing list
>>> 
>>> to Send a Message to the list, use the email address
>>> Gasification at bioenergylists.org
>>> 
>>> to UNSUBSCRIBE or Change your List Settings use the web page
>>> http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> 
>>> for more Gasifiers,  News and Information see our web site:
>>> http://gasifiers.bioenergylists.org/
>>> 
>>> -------------- next part --------------
>>> An HTML attachment was scrubbed...
>>> URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121010/363fff21/attachment-0001.html>
>>> 
>>> ------------------------------
>>> 
>>> Message: 12
>>> Date: Wed, 10 Oct 2012 11:43:32 -0300
>>> From: "Kevin" <kchisholm at ca.inter.net>
>>> To: "Discussion of biomass pyrolysis and gasification"
>>>         <gasification at lists.bioenergylists.org>
>>> Subject: Re: [Gasification] Gasification of Corn cob
>>> Message-ID: <8D2E38E8D32A47959238F410FB90BDC8 at usera594fda0bf>
>>> Content-Type: text/plain; charset="iso-8859-1"
>>> 
>>> Dear Tom
>>> 
>>> I would agree with you that a Top Lit Updraft Gasifier, operated in a batch mode would be great for producing "Heating Grade Gas" (HGG), when there was a desire to also produce charcoal.  However, if Masi was interested in maximum use of the corncobs for producing HGG, then a "top lit gasifier system" would not appear to be the best approach, because the charcoal left over would be undesirable. Additionally, there is the problem of a "batch operation."
>>> 
>>> If Masi wanted a gasifier system to produce a woodgas suitable for powering an Internal Combustion engine, I cannot see how the Top Lit Gasifier could possibly produce an Engine Grade Gas. (EGG) I would suggest that it would have excessive tar, that would make it useless for fuelling an IC Engine. Additionally, there is the inherent problem of the batch nature of the TLUD gasifier.
>>> 
>>> As I see it:
>>> 1: The TLUD gasifier is great for use with a close coupled burner system, where there is a wish to produce a residual charcoal, and where batch operation is acceptable.
>>> 2: A TLUD gasifier is not appropriate for producing Engine Grade Gas, because of an unacceptably high tar content.
>>> 3: A TLUD gasifier is not appropriate unless it is desired to produce a charcoal by-product.
>>> 
>>> I might be missing something, but do you know of any way that a TLUD can produce engine Grade Gas?
>>> 
>>> Best wishes,
>>> 
>>> Kevin
>>> 
>>> ----- Original Message -----
>>> From: "Thomas Reed" <tombreed2010 at gmail.com>
>>> To: "Discussion of biomass pyrolysis and gasification" <gasification at lists.bioenergylists.org>
>>> Sent: Wednesday, October 10, 2012 10:19 AM
>>> Subject: Re: [Gasification] Gasification of Corn cob
>>> 
>>> 
>>> > Dear Masi
>>> >
>>> > I have never run a gasifier on corn cobs, but I believe they would be an excellent fuel as long as the moisture content is <15%. Be sure to operate lighting the TOP of the pile so that the char sits above the unburned fuel.
>>> >
>>> > Write me -send a picture- if you can.
>>> >
>>> > Yours truly,
>>> >
>>> > Tom Reed
>>> >
>>> > Thomas B Reed
>>> >
>>> >
>>> > On Oct 10, 2012, at 5:02 AM, masi karuppu <masikaruppu at gmail.com> wrote:
>>> >
>>> >> Dear Sir,
>>> >>
>>> >> I would like to know about the operating performance of a gasifier
>>> >> which works on Corn cob as fuel input.
>>> >>
>>> >> Thanks and regards
>>> >> K.Subramaniam
>>> >>
>>> >> _______________________________________________
>>> >> Gasification mailing list
>>> >>
>>> >> to Send a Message to the list, use the email address
>>> >> Gasification at bioenergylists.org
>>> >>
>>> >> to UNSUBSCRIBE or Change your List Settings use the web page
>>> >> http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> >>
>>> >> for more Gasifiers,  News and Information see our web site:
>>> >> http://gasifiers.bioenergylists.org/
>>> >
>>> > _______________________________________________
>>> > Gasification mailing list
>>> >
>>> > to Send a Message to the list, use the email address
>>> > Gasification at bioenergylists.org
>>> >
>>> > to UNSUBSCRIBE or Change your List Settings use the web page
>>> > http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> >
>>> > for more Gasifiers,  News and Information see our web site:
>>> > http://gasifiers.bioenergylists.org/
>>> -------------- next part --------------
>>> An HTML attachment was scrubbed...
>>> URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121010/8a9f663e/attachment-0001.html>
>>> 
>>> ------------------------------
>>> 
>>> Subject: Digest Footer
>>> 
>>> _______________________________________________
>>> Gasification mailing list
>>> 
>>> to Send a Message to the list, use the email address
>>> Gasification at bioenergylists.org
>>> 
>>> to UNSUBSCRIBE or Change your List Settings use the web page
>>> http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>>> 
>>> for more Gasifiers,  News and Information see our web site:
>>> http://gasifiers.bioenergylists.org/
>>> 
>>> 
>>> 
>>> ------------------------------
>>> 
>>> End of Gasification Digest, Vol 26, Issue 6
>>> *******************************************
>> 
>> 
>> _______________________________________________
>> Gasification mailing list
>> 
>> to Send a Message to the list, use the email address
>> Gasification at bioenergylists.org
>> 
>> to UNSUBSCRIBE or Change your List Settings use the web page
>> http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
>> 
>> for more Gasifiers,  News and Information see our web site:
>> http://gasifiers.bioenergylists.org/
> 
> _______________________________________________
> Gasification mailing list
> 
> to Send a Message to the list, use the email address
> Gasification at bioenergylists.org
> 
> to UNSUBSCRIBE or Change your List Settings use the web page
> http://lists.bioenergylists.org/mailman/listinfo/gasification_lists.bioenergylists.org
> 
> for more Gasifiers,  News and Information see our web site:
> http://gasifiers.bioenergylists.org/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.bioenergylists.org/pipermail/gasification_lists.bioenergylists.org/attachments/20121012/bcceb630/attachment.html>


More information about the Gasification mailing list