[Greenbuilding] ***SPAM*** Re: ***SPAM*** Re: air barrier recommendations

[Reuben Deumling]

Thank you, John, for the detailed reply.
I have interspersed some comments below,

On Tue, Jul 12, 2022 at 5:35 AM John Straube <jfstraube at gmail.com> wrote:

> If you skip the plywood in OSP then you will need to use a standard
> membrain product such as Tyvek. Is there any reason you would not use the
> obvious?
>

I am not using plywood chiefly because for buildings like this (style,
size) I believe they have *structurally* done OK without it, and it hadn't
occurred to me that plywood offered *air sealing* benefits sufficient to
justify the effort/cost/etc.

Also you were asking about the air barrier but really the most fundamental
> requirement of a shed or a hospital is rain control. Thus providing lapped
> housewrap under the siding and over the framing is fundamental and
> critical. Much more important than an air barrier.


That is what I was originally intending to use, but when I looked more
closely at those I realized they tend to be woven instead of continuous
like tyvek (so expensive!) Which prompted my questions here. But if a woven
house wrap product is suitable here I am happy to use it.

We often call the rain control layer in a roof in a underlayment when it is
> placed below roofing that does not leak too much such as metal roofing and
> Ashfall shingles. You could use Tyvek for this as well but it is too
> slippery to work with and hence special grippier products are widely used.
> The benefit of large sheets of polymer are that they are strong enough and
> have few enough joints that you can tape them as an air barrier once you
> have properly gravity lap them for rain control.


I have long used 30lb felt in this application but really don't care for
its properties. I know there are fancier (special, grippier) products but
have not yet investigated those.


> Providing air barrier continuity between the roof membrane which is above
> the framing and the wall membrane which is to the exterior of the framing
> is a bit more complicated but for a shed simply installing blocking and
> sealing with caulking around the edges should be sufficient.
>

Thanks, that makes sense.


> There is no good answer for under your floor since what you are proposing
> is just considered "bad practice". That said I have several projects in my
> own property that to do some thing similar although they do provide at
> least 6 inches of clear air over the soil. These projects of mine are small
> 10' x 10' sized buildings that are not intended to be durable and in fact
> are likely to begin to have floor rot in 10 to 20 years of service. To
> locate a wood-based floor system directly on grade you would need to use
> something you probably don't like that is a foam plastic insulation on the
> underside of the wood protecting it from water vapour flow and keeping the
> framing at a different temperature than the grade. You will likely say you
> are not placing it on grade but you are clearly placing it so close to the
> grade it's almost the same.


I am surprised that 12" (range currently is between 8" and 16"j is
considered to be equivalent to placing it on grade. Are you saying the air
gap + whatever
membrane would not offer meaningful protection for the wood over time?


> This one and a half or 2 inch foam layer underneath the wood will allow
> for a long term durable floor system. In your climate I would not bother
> putting fibrous insulation between the floor joists.
>

I am open to foam. Had not considered it. I think I even have a stash of
that stuff left over from another job. I take it you would suggest screwing
the foam to the joists using those big plastic washers? And, presumably my
method of building the floor sections upside down would be acceptable? I'd
plan to keep the foam inboard of the sill plate.

>
> > On Jul 11, 2022, at 18:53, Reuben Deumling <9watts at gmail.com> wrote:
> >
> > Portland Oregon, dry hot summers; high humidity in the winter.
> >
> > I should have mentioned that I am skipping the plywood altogether. I am
> putting up rough sawn board-and-batten siding over the studs and blocking.
> My thought was to put that air barrier between those.
> >
> > On Mon, Jul 11, 2022 at 3:35 PM John Straube <jfstraube at gmail.com>
> wrote:
> > Hey there Reuben.  A description of your climate would be helpful before
> I weigh in..
> > In most cases taping up the plywood or osb sheathing would often be a
> great solution.
> >
> > On Mon., Jul. 11, 2022, 18:15 Reuben Deumling, <9watts at gmail.com> wrote:
> > I hope there are still a few of you smart people out there. This list
> used to be so fun!
> >
> > I'm a little rusty on this stuff. So your thoughts are much appreciated.
> >
> > I am building a 250 sf shop in my back yard. I am insulating the floor
> right away (R19 FG batts) and the walls and 12/12 metal roof plane sometime
> in the future. My hope is to affix a barrier of some sort (6 mil plastic?)
> to the underside of the joists (ca. 12" unvented crawl space beneath), and
> wrap the walls and roof plane with some sort of air barrier, but am not
> sure what a good product choice would be for
> > - under the floor
> > - the walls
> > - the roof
> >
> > Thanks for all suggestions.
> >
> > Reuben
> > _______________________________________________
> > Greenbuilding mailing list
> > to Send a Message to the list, use the email address
> > Greenbuilding at bioenergylists.org
> >
> > to UNSUBSCRIBE or Change your List Settings use the web page
> >
> http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org
> > _______________________________________________
> > Greenbuilding mailing list
> > to Send a Message to the list, use the email address
> > Greenbuilding at bioenergylists.org
> >
> > to UNSUBSCRIBE or Change your List Settings use the web page
> >
> http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org
> > _______________________________________________
> > Greenbuilding mailing list
> > to Send a Message to the list, use the email address
> > Greenbuilding at bioenergylists.org
> >
> > to UNSUBSCRIBE or Change your List Settings use the web page
> >
> http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org
>
>
> _______________________________________________
> Greenbuilding mailing list
> to Send a Message to the list, use the email address
> Greenbuilding at bioenergylists.org
>
> to UNSUBSCRIBE or Change your List Settings use the web page
>
> http://lists.bioenergylists.org/mailman/listinfo/greenbuilding_lists.bioenergylists.org
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.bioenergylists.org/pipermail/greenbuilding_lists.bioenergylists.org/attachments/20220712/9299fd1a/attachment.html>