[Stoves] radiant heat capture, total heat measurement
rongretlarson at comcast.net
rongretlarson at comcast.net
Sat Mar 10 15:08:44 CST 2012
Paul etal
Nice short 13 second video. Very clear.
Is it possible to repeat a timed boiling test with the only difference being whether there is a strainer in or out? Might also try different pots, artificially changing the pot height , etc Anything to give more numerical values.
This is is to more exactly quantify your earlier observation that the input energy seemed to be about a doubling.
Ron
----- Original Message -----
From: "Paul Olivier" <paul.olivier at esrla.com>
To: rongretlarson at comcast.net
Cc: "Discussion of biomass cooking stoves" <stoves at lists.bioenergylists.org>, "Andrew Heggie" <ajheggie at gmail.com>, "Crispin Pemberton-Pigott" <crispinpigott at gmail.com>
Sent: Saturday, March 10, 2012 1:33:24 PM
Subject: Re: [Stoves] radiant heat capture, total heat measurement
Ron,
This is not a very good video clip, but it does show the entire 150 gasifier:
http://youtu.be/8IcXDAK37gA
This is a rough prototype made by hand.
The mass-produced product should look better.
Also I do not envision that this gasifier be operated as a stand-alone device.
For safety reasons it should be set within a counter-top enclosure, as seen here:
http://dl.dropbox.com/u/22013094/150%20Gasifier/Jpegs/008.jpg
Thanks.
Paul
On Sun, Mar 11, 2012 at 2:48 AM, Paul Olivier < paul.olivier at esrla.com > wrote:
Ron,
I did yesterday an experiment with aluminum foil to reflect back up the thermal radiation emitted from the dome.
The aluminum starts to wrinkle and crack well before the burn is complete.
Also I tried yesterday a wire mesh of an aperture of 30 mesh.
This did not work as well as what I am using now (a stainer that I bought in the market).
I have yet to find the factory that makes this strainer,
and I do not have the instrument that is needed to measure its aperture.
Ron, I think that the foam that you have found offers the most promise.
I am sure that this foam will deliver more radiant energy than stainless steel wire mesh.
Also I hope to employ a type of funnel that would surround the dome and
focus the laterally emitted thermal radiation toward the pot.
Finally the pot has to absorb and not reflect.
Thanks.
Paul
On Sun, Mar 11, 2012 at 1:58 AM, < rongretlarson at comcast.net > wrote:
<blockquote>
Andrew, Paul, Crispin, list:
1. The last several paragraphs below are coming out more negatively on radiant heat capture than I think are appropriate. Remember, the initial information provided by Paul Olivier on March 2, when he said:
"When a wire mesh dome is placed on top of the burner and burner housing,
this roughly doubles the amount of heat being transferred to a pot: "
2. I think this doubling has little to do with the exchange below (and a few earlier that are similar). Radiant heaters are widely sold because of their efficiency in heat transfer - in many cases involving zero convection. Given we have only one (above) piece of data for one stove, the chances are that a doubling is not the maximum we can achieve.
3. I would look at this as a conservation of energy problem. We know that we can transfer more energy to the pot if the radiator is hotter. There may be catalysts that we can employ. We know how to use reflectors and obtain high absorption (and sometimes simultaneously low emissivity)
In my reading on ceramic foam, I found that some foam is being employed so as to have gas combustion take place inside the foam!.
4. I hope that others can perform some experiments along these lines.
Ron
From: ajheggie at gmail.com
To: "Discussion of biomass cooking stoves" < stoves at lists.bioenergylists.org >
Sent: Saturday, March 10, 2012 3:31:17 AM
Subject: Re: [Stoves] radiant heat capture, total heat measurement
On Fri, 9 Mar 2012 12:25:49 +0200, Crispin Pemberton-Pigott wrote:
>>...and passes visible light and higher frequency infra red from hot bodies,
>like the sun,
>
>
>
>Most of it, the rest makes it warmer (absorbs).
Yes that which it absorbs make it warmer but equally as a warm body at
equilibrium it will be re emitting longer wavelength IR.
>
>
>
>>but absorbs the lower energy infra red from cooler bodies like earth and
>our bodies.
>
>
>
>Yes, and because it is warm, and active in the IR, it also emits IR but with
>a low emissivity. In other words if you know the emissivity, you can read
>the temperature with an IR gun.
it is emitting a different (lower) frequency from which it has
absorbed.
>
>
>
>But more to the point I was saying that at a lower (non 90°) angle, it
>starts to reflect radiation from the top of the surface. Look at glass at a
>low angle and it looks like a mirror.
Agreed
>
>
>
>The point is that when reflecting heat, if the incident angle is past a
>critical value, it reflects pretty much all of it so the issues Kevin
>mentioned about the mirroring on the back don’t come into play.
This depends on the refractive index of the two materials, going from
a lower to higher there is always some light transmission, the other
way round and you have total reflection, this is how a light fibre
works.
>
>
>
>Paul’s question was about reflecting the heat. So the principles are the
>reflectivity, surface finish, incident angle and emissivity. While a stove
>may be good at sending IR radiation towards the pot, pots are not all that
>good at picking it up, actually. Stainless steel pots are quite reflective
>and do better picking up heat by convection.
The major salient point is that radiation from heating something by
flame/flue gases is only ever going to extract a minor portion of the
heat in the gas stream. Consider a black body in the gas flow, it can
never be hotter than the gas flow downstream of it, as you make it
hotter it radiates more heat but the rejected gas flow is also hotter,
either way you still need to have the convection do most of the work.
AJH
_______________________________________________
Stoves mailing list
to Send a Message to the list, use the email address
stoves at lists.bioenergylists.org
to UNSUBSCRIBE or Change your List Settings use the web page
http://lists.bioenergylists.org/mailman/listinfo/stoves_lists.bioenergylists.org
for more Biomass Cooking Stoves, News and Information see our web site:
http://www.bioenergylists.org/
--
Paul A. Olivier PhD
27C Pham Hong Thai Street
Dalat
Vietnam
Louisiana telephone: 1-337-447-4124 (rings Vietnam)
Mobile: 090-694-1573 (in Vietnam)
Skype address: Xpolivier
http://www.esrla.com/
</blockquote>
--
Paul A. Olivier PhD
27C Pham Hong Thai Street
Dalat
Vietnam
Louisiana telephone: 1-337-447-4124 (rings Vietnam)
Mobile: 090-694-1573 (in Vietnam)
Skype address: Xpolivier
http://www.esrla.com/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.bioenergylists.org/pipermail/stoves_lists.bioenergylists.org/attachments/20120310/1efeb827/attachment.html>
More information about the Stoves
mailing list