[Stoves] Boiled 520 grams of 14C water in 3:20 minutes

[Jonathan P Gill]

Paul,

Good to hear from you.

Here are a few pictures I hope will help answer your question.  

The design I am working on was informed by the work of Prof. Bolinio and Paul Oliver.  They place a cap, a burner plate with two rings of holes for blue flamelets,  over the reactor and only introduce secondary air above the cap.  The cap effectively seals the reactor chamber, preventing any secondary air from entering.  This creates something of a hybrid between a TLUD and a Retort: a TLUD with a a bit of Retort flavor.

I do the much the same, but do not use the 80 holes in their design for the burner plate. My solid burner plate is sized to allow for a gap between the wall of the reactor chamber and the edge of the plate.  Thus the gases emerge from the reactor via this gap at the edge.  They can thus only meet secondary air above the gap.  Secondary air is thus prevented from entering the pyrolysis chamber - as per Bolinio and Olivier.


Bottom view of primary air system - now 5/64 of an inch holes.




Top view showing the support brackets.  
I no longer use the washers and now rotate the brackets slightly to form fingers to support the burner plate.

This reactor can is the only part of the Rim Fire iCan that should be made of high temperature stainless.



Burner plate in place.  The gap is slightly below the rim of the can.
The notch is not required or desired. It is an artifact.
I will be trying a slightly larger plate to see if the gap can be narrowed some.



Detail of the above.

I hope this answers your questions.

Regards,

Jock

Jonathan P Gill
Peacham, VT.
jg45 at icloud.com

Extract CO2 from the atmosphere. 





On May 5, 2013, at 3:44 PM, Paul Anderson <psanders at ilstu.edu> wrote:

> Jock,
> 
> I did not understand
>> 
>> Not having any secondary air introduced into the pyrolysis chamber is brilliant.  I wish I had thought of it
> Please explain, or re-send how you explained it before.
> 
> Paul
> Paul S. Anderson, PhD  aka "Dr TLUD"
> Email:  psanders at ilstu.edu   Skype: paultlud  Phone: +1-309-452-7072
> Website:  www.drtlud.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.bioenergylists.org/pipermail/stoves_lists.bioenergylists.org/attachments/20130505/50ef00ff/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Reactor - bottom view.jpeg
Type: image/jpg
Size: 104558 bytes
Desc: not available
URL: <http://lists.bioenergylists.org/pipermail/stoves_lists.bioenergylists.org/attachments/20130505/50ef00ff/attachment.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: reactor - top view.jpeg
Type: image/jpg
Size: 103630 bytes
Desc: not available
URL: <http://lists.bioenergylists.org/pipermail/stoves_lists.bioenergylists.org/attachments/20130505/50ef00ff/attachment-0001.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Burner plate in place.jpeg
Type: image/jpg
Size: 73977 bytes
Desc: not available
URL: <http://lists.bioenergylists.org/pipermail/stoves_lists.bioenergylists.org/attachments/20130505/50ef00ff/attachment-0002.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Rim Fire gap 1.jpeg
Type: image/jpg
Size: 79862 bytes
Desc: not available
URL: <http://lists.bioenergylists.org/pipermail/stoves_lists.bioenergylists.org/attachments/20130505/50ef00ff/attachment-0003.jpg>